Princeton Tec SNAP SOLO Instructions D'utilisation Et D'entretien

SNAP SOLO
®
LED HEADLAMP
Operating and Maintenance Instructions
ENGLISH:
Battery Installation
– See Battery Installation Diagram
• 3 AAA
• Alkaline (LR03) or Lithium
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and
recommends recycling batteries. For more information
about battery recycling, please go to www.
batteryrecycling.com.
To install batteries, first remove the light body from the
mounting bracket. Slide the battery door latch toward
front of light and rotate the door open. Install three AAA
batteries oriented so each negative terminal contacts a
corresponding spring. Observe proper battery polarity
when installing the batteries. Improper installation of the
batteries will damage the light and void the warranty.
Rotate the door toward the closed position, and then
squeeze the door and body to latch the door.
!
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
Switch Operation
– See Figure 2
From off:
On / high
Single press:
Press & hold dimming
The LED will blink once when it has reached minimum or
maximum brightness.
flash
Triple press:
off
Single press (from any mode):
Lockout – Snap headlamp design incorporates a
mechanical lockout – rotate the light body up fully to
protect the button from accidental activation during
storage or transport.
Troubleshooting
If the Snap fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check circuit board for water. The light will resume
normal operation once the water is shaken or blown out
and the light is left open until completely dry. If the light
has been contaminated with salt water, flush the unit
with fresh water and dry as described above.
Figure 1 – Battery Replacement
1
Figure 2 – Switch Operation
Figure 3 – Performance
Modes Lumens Runtime
HIGH SPOT 300 10h
LOW SPOT 10 155h
STROBE 300 130h
DISTANCE (m)
(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value—defined as 30 seconds after the
point the device is first turned on—using fresh batteries, until the light output reaches 10% of the initial value.
Reserve time is the duration of time from 10% of initial light output value down to 0.25 lux
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to
be free from defects in workmanship and materials
under normal use for 5 years. This warranty covers all
of the component parts of the product except batteries.
This warranty does not cover deterioration due to
normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair. Princeton
Tec will repair or replace parts which are defective in
workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton
Tec are the only facilities authorized to repair the
product. After (3) unsuccessful attempts (within the
warranty period) to repair the product, you have the
right to elect replacement of the product or a refund
of the purchase price less allowance for use of the
product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARE INCLUDED IN THIS WARRANTY. (Some states do
not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a
chemical known to the State of California to cause birth
defects or other reproductive harm.
2 3
Press 1x:
On / High
Press and Hold:
Dimming
Rotate light body upwards
Lockout
Beam Pattern
0 7
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first
contact Princeton Tec customer service on
1-800-257-9080 to request an RMA number. Please
have your light model, date of purchase and a brief
description of the fault you are experiencing. No
warranty repairs will be accepted without an RMA
number.
3. Return the light without batteries to: Princeton Tec,
PO Box 8057 Trenton NJ 08650. Postage due and
freight collect items will not be accepted.
4. Upon receipt your light will be processed in about
two weeks. Please allow additional time for return
transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
4
(From on):
Press 3x:
Flash
(From on):
Press 1x from On:
Off
Reserve
100h
7h
20h
30 50