Publicité
Les langues disponibles
Les langues disponibles
EN
I undersigned Rudy Bigand, Technical Director of the company Sammode SA, located at 24 rue des Amandiers 75020
PARIS, declares that following products (group IIIC category 2D and group IIC category 3G) :
‐
LFSn 118, KEPLER 1x18 ‐ 1 lamp T8 18 W G13 / Classe 1 ou 2 / 230 Volts / 50/60 or 50/60/0Hz
‐
LFSn 136, KEPLER 1x36 ‐ 1 lamp T8 36 W G13 / Classe 1 ou 2 / 230 Volts / 50/60 or 50/60/0Hz
‐
LFSn 158, KEPLER 1x58 ‐ 1 lamp T8 58 W G13 / Classe 1 ou 2 / 230 Volts / 50/60 or 50/60/0Hz
‐
LFSn 218, KEPLER 2x18 ‐ 2 lamps T8 18 W G13 / Classe 1 ou 2 / 230 Volts / 50/60 or 50/60/0Hz
‐
LFSn 236, KEPLER 2x36 ‐ 2 lames T8 36 W G13 / Classe 1 ou 2 / 230 Volts / 50/60 or 50/60/0Hz
‐
LFSn 258, KEPLER 2x58 ‐ 2 lamps T8 58 W G13 / Classe 1 ou 2 / 230 Volts / 50/60 or 50/60/0Hz
meet the following regulatory requirements:
ElectroMagnetic compatibility Directive (EMC) 2014/30/EU
To ensure compliance the product meets specific standards lighting fixtures: EN 55015 relating to radio disturbance
and EN 61547 on immunity. Moreover, the active components are themselves in conformity with the EMC Directive
Low Voltage Directive (LVD) 2014/35/EU
To ensure compliance the product meets the standards of fixtures series EN 60598, the active components are
themselves consistent with the LVD.
All equipment leaving the assembly shall be test operation and safety, especially dielectric and earthing continuity.
Environmental Directives
Directives 2011/65/EU (on the restrictions on the use of certain hazardous substances in Electrical and Electronic
Equipment) Directive 2012/19/EU and (Known as WEEE, Waste Electrical and Electronic Equipment).
ATEX Directive 2014/34/EU
To ensure compliance the product meets the followings standards :
‐
EN 60079‐0:2012/A11 :2013 (Explosive Atmospheres ‐ Equipment – General requirements),
‐
EN 60079‐15 :2010 (Electrical apparatus for explosive gas atmospheres – Part 15: Construction, test and
marking of type of protection "n" electrical apparatus)
‐
EN 60079‐31 : 2014 (Explosive atmospheres ‐ Part 31: Equipment dust ignition protection by enclosure "t").
Nevertheless the respect of current standards at the hereby declaration, EN 60079‐31 : 2014, has no impact
on the product
‐
The EC‐type examination certificates INERIS 03 ATEX 0011X and The type examination certificates INERIS 03
ATEX 3004X delivered by the notified body INERIS, 0080, F‐60 550 Verneuil‐en‐Halatte.
Products are manufactured according to our notified quality system
n° 0080, F‐60550 Verneuil‐en‐Halatte.
Sammode SA
24, rue des Amandiers – F 75020 Paris
EU CONFORMITY DECLARATION
Paris 13 October 2017
RUDY BIGAND
Technical Director
INERIS 04ATEXQ705
8/12
issued by
INERIS,
Notice KEPLER rév.K
Octobre 2017
Publicité
