stayer GRASS CUTTER L20 Instructions D'emploi page 22

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates
of our machines on the website: www.grupostayer.com
APPLICATION
1.
Depending on the assembled cutting tools, the bush cutter
can be used to mow lawns or meadows, and to trim scrub,
shrubs, bushes and very small trees.
WARNING! Read this manual and general safety
instructions carefully
appliance, for your own safety. Your power tool
should only be passed on together with these
instructions.
OVERVIEW COMPONENTS (FIG A)
2.
1 Blade or cutting line
2 Telescopic stand
3 Protection carter
4 Ignition switch
5 Safety device
6 Auxiliary handle
7 Telescopic stand height adjustment
8 Spool guard
9 Head angle button
10 Head angle fixing nut
11 Battery (s)
12 Inverted turn switch
13 Harness anchor
14 Harness
15 Dual grip position adjustment
16 Nylon spool holder
GENERAL SAFETY INSTRUCTIONS
3.
Read all safety warnings and instructions.
Working area
- Keep working area clean and well lit. Untidy and dark
areas can lead to accidents.
- Do not operate
surroundings, for example, in the presence of
inflammable liquids, gases or dust. Tools create sparks
which may ignite the dust or fumes.
- Keep children and bystanders at a distance when
operating a tool. Distractions can cause you to lose
control of it.
Personal safety
- Stay alert, watch what you are doing and use common
sense when operating a tool. Do not use a tool when
you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention when operating a
tool may result in serious personal injury.
before using
tools in potentially
ENGLISH
22
- Use safety equipment. Always wear eye protection.
Using safety equipment such as a dust mask, non-
skid safety shoes, a hard hat, or hearing protection
whenever it is needed will reduce the risk of personal
injury.
- Remove any adjusting keys or spanners before turning
on the tool. A spanner or key left attached to a rotating
part of the tool may result in personal injury.
- Do not reach out too far. Keep your feet firmly on the
ground at all times. This will enable you retain control
over the tool in unexpected situations.
the
- Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from the
tool. Loose clothes, jewellery or long hair can become
entangled in the moving parts.
- Inspect the entire machine for loose parts (nuts, bolts,
screws, etc.) and any damage. Repair or replace as
necessary before using the machine.
- DO NOT USE any attachment with this power head
other than the ones recommended by our company.
Serious injury to the operator or bystanders could
result as well as damage to the machine.
- The blade guard and front handle guard is very
important to the machine. It must be screwed up on
the machine before the initial use. These guards must
always be fixed when operating the machine. Check
these guards before each use. If any damage (crack,
break, etc.) on the guard, contact with your dealer for
replacing it.
- If use of non-conformant replacement guards, or
remove or modify these guards could result in serious
injury to the operator or bystanders.
- Always use proper handles and shoulder strap when
cutting.
- Do not use the unit if it is damaged or poorly adjusted.
Never remove the machine's guard. Serious injury
to the operator or bystanders could result as well as
damage to the machine.
- Inspect the area to be cut and remove all debris that
could become entangled in the nylon cutting head.
Also remove any objects that the unit may throw during
cutting.
- Never leave the machine unattended.
explosive
- Do not use this unit for any job other than those for
which it is intended as described in this manual.
- Do not overreach. Keep proper footing and balance at
all times. Do not run the unit while standing on a ladder
or on any other unstable footing location. Appropriately
use the harness provided when operating the machine.
- Keep hands and feet clear of the nylon cutting head or
blade while unit is in use.
- Do not use this type of machine for sweeping away
debris.
- Use nylon cutting head which is free of damage. If a
stone or any other obstacle is hit, stop the engine and
check the nylon cutting head. A broken or unbalanced
nylon cutting head must never be used.
- When ever approaching an operator of the machine,
carefully call his attention and confirm that the operator
stop the engine. Be careful not to startle or distract the
22