Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
INPUT AND OUTPUT DISPLAY DETAILS
KTB500 display is intended to provide real-time input and output performance data on all ports combined, individually, and if specific output protocols are being utilized.
UNITS BUTTON
Press to obtain input and output parameters in Watts (W), Watt-hour (Wh), Volts (V), and Current (A), as applicable. Press the button and the unit icon on the
screen will change with updated performance results.
INFO BUTTON
Press to cycle input and output from all ports, or individual ports (as applicable).
DISPLAY BUTTON
Press the DISPLAY button to illuminate the LCD for 60 seconds. Press and hold the DISPLAY button longer than 3 seconds, to keep LCD illuminated
indefinitely. The display will flash on/off to alert the user that it will remain on, pressing the DISPLAY button will turn the display off.
BATTERY LEVEL
E
: The battery level is provided by percentage of battery charge corresponding to the number of bars and percentage displayed. The bars in the battery level
correspond to the current state of charge, 0-20%, 21-40%, 41-60%, 61-80%, and all five are lit when charge level is above 81%.
TIME UNTIL EMPTY/FULL
G
: Provides the user live telemetry data on time to completely charge, or deplete the battery based upon the energy entering or leaving the battery. Please
be aware that this value can adjust multiple times as the energy draw changes from the connected devices. This is evident during initial activation of ports with a connected device.
INPUT
D
: The KTB500 is capable of providing input energy in watts, watt-hr, or amps.
OUTPUT
H
: The display will provide output characteristics of all ports, including 12V car port, AC ports, and USB ports. The details on this function are provided below in the
OPERATING INSTRUCTIONS section. The output wattage displayed by the power station will be accurate to within 10%.
COOLING FAN
: KTB500 utilizes an internal cooling fan to ensure the product is operating within the appropriate temperature range. The unit, when it experiences a higher
B
output load, will automatically turn on the fan. During discharge, and possibly charging, the fan may operate intermittently to keep internal temperature within operating range. The
fan will likely start when the AC circuit is activated to ensure proper operation.
CHARGING KTB500
Only charge unit with provided AC wall charger, Klein Cat. No. 29201, 12V car port charger, Klein Cat. No. 29209, or APP
Charge unit indoors.
Connect the provided AC Wall Charger
along with time until full
G
. The unit is fully charged when the level is 100. It is recommended to fully charge KTB500 every 3 months to maintain the health of the battery pack.
POWERING /
CHARGING DEVICES WITH KTB500
Select the type of outlet required by pressing the USB Output ON/OFF Button
is pressed to activate the port. When activated, the indicator on the button will illuminate green, indicating that the output(s) are active, and the LCD display will turn on and provide
details on the charging output. Press the ON/OFF button(s) to shut down the output(s) when not in use. The LCD will automatically shut down when no outputs are activated.
KTB500 will enter sleep mode after 90 seconds of inactivity (no output load detected) and will "wake up" when inputting a charging cord or when any button is pressed.
PASS-THROUGH CHARGING
The advanced battery management system of the KTB500 allows it to charge a connected device while the wall charger unit is plugged into the KTB500. The KTB500 is capable
of supporting more output than can be provided by the wall charger input. Therefore, the KTB500 may still be depleting battery capacity depending upon the load required by the
connected device being charged.
OVERLOAD CONDITION
If the LCD displays the overload condition symbol ("OL"); do the following:
• Turn off USB ports
and AC outlets
2
• Disconnect all devices, including the KTB500's charging cord.
• Verify the maximum power requirements for all devices, and confirm that the device power requirements do not exceed KTB500's capacity (see GENERAL SPECIFICATIONS).
• Reconnect only necessary devices.
• Turn on USB ports and/or AC outlets and resume operation.
If an overload condition occurs on the input port, the portable battery will automatically shut off the input port. The port will be reactivated when the input source meets the
specification outlined in the GENERAL SPECIFICATIONS section. Only charge the unit with provided AC wall charger.
KLEIN TOOLS ACCESSORY MOUNT
To attach a Klein Tools accessory to KTB500, such as the AEPJS1 Wireless Jobsite Speaker, or 55437 Tradesman Pro
flange with the slots on KTB500's Accessory Mount, then insert and rotate clockwise to lock into place. To remove the accessory, rotate counterclockwise and pull out.
4
DETAILS DISPLAYED ON LCD
OPERATING INSTRUCTIONS
to the AC Charger input
, and allow KTB500 to fully charge prior to use, approx. 9 hours. The LCD display will provide charge level
15
5
. The green indicator light will no longer be illuminated when the ports / outlets are turned off.
14
17
FUNCTION BUTTONS
or the AC Outlet ON/OFF Button
2
14
to 8mm adapter, Klein Cat. No. 29205 (105W max input).
®
. The outlet port will NOT function until the appropriate button
Worklight, align the tabs on the accessory's mounting
TM
E
,
Publicité
