Ketra G21210BTGR33AWH/BK Manuel D'installation page 8

P R E - I N S TA L L AT I O N
• Products are connected end-to-end via the integrated connectors at each
end of product. Note that there is an "input" and "output" connecter on each
Note:
product and orientation is critical. A common mistake made is to install the
products backwards. Jumper cables may be inserted in between fixtures in
Products are connected end-to-end via the integrated connectors at each end of the product.
-
order to make installation easier.
Note that there is an "input" and "output" connecter on each product and orientation is critical.
A common mistake made is to install the products backwards. Jumper cables may be inserted in
between fixtures in order to make installation easier.
3
SIGNAL
GROUND
NEUTRAL
LINE
120VAC, 60 Hz
MAINS SUPPLY
fig. 4
N3 TO G2 LEADER CABLE
DETAIL VIEW
50 ft (15.2 m) leader cable max
-
• 50 foot leader cable max
40 ft (12.1 m) of G2 Linear fixtures
-
• 40 feet of G2 Linear fixtures
100 ft (30.4 m) total run max, including leader cable, fixtures, and jumper cables
-
• 100 feet total run max, including leader cable, fixtures, and jumper cables
A typical installation includes:
A typical installation includes:
• N3 Satellite
• N3 Satellite
• Leader cable with terminator
• Leader cable with terminator
• 1 to 40 G2 Linear fixtures
• 1 to 40 G2 linear fixtures
• Optional jumper cables as needed
• The G2 has mounting feet that have one thru hole on each side.
• Optional jumper cables as needed
• Attach the product to a flat surface using appropriate #8, #9, or
• The G2 has mounting feet that have one thru hole on each side
#10 countersunk fasteners (e.g. wood screws, sheet metal screws .)
• Attach the product to a flat surface using appropriate #8, #9, or #10 countersunk fasteners (e.g., wood
screws, sheet metal screws)
G2 INSTALLATION GUIDE
8 | G2 INSTALLATION GUIDE
PR E- I N S TA LL ATI O N
G2 LEADER CABLE TO G2
DETAIL VIEW
G2 LEADER CABLE
OUTPUT
L1 G2L
KETRA N3
N3 POWER & SIGNAL
OUTPUT
SIGNAL
GROUND
NEUTRAL
LINE
G2 LEADER CABLE
INPUT
770-0000XX-0X-0X
G2
INPUT
G2
G2J
G2 G2
IN
G2
L1 G2L
KETRA N3
120VAC, 60 Hz
G2
MAINS SUPPLY
STAR TOPOLOGIES ARE NOT SUPPORTED
G2 TO G2
DETAIL VIEW
OUTPUT INPUT
OUT
G2
G2
G2
KEY
L1 12 AWG, 3 WIRE
G2L KETRA G2 LEADER CABLE
G2J KETRA G2 JUMPER CABLE
KETRANET MESH
WIRELESS NETWORK
PAGE 8
P/N 3662343 Rev B
© 2019 Ketra, Inc. All rights reserved.
3815 S. CAPITAL OF TE
SUITE 100
AUSTIN, TX 787
P: 512.347.110
GENERAL NOTES:
1. KETRANET MESH IS KETRA'S
CONTROL PROTOCOL.
2. A NODE IS A KETRANET MES
WIRELESS DEVICE.
3. 50 KETRANET MESH NODES
INSTALLATION NETWORK.
4. ALL KETRANET MESH NODE
INSTALLED WITHIN 50'-0" RA
NEAREST NODE.
5. PER N3: MAX. FIXTURE QTY:
MAX. RUN LENGTH: 100FT
FOR REFERENCE
NOT FOR
CONSTRUCTI
DRAWING TYPE: OL
DRAWING #:
REVISION #: 00
04/11/2016
DATE:
DRAWN BY: GEB
CHECKED BY: CEH
SCALE:
NTS
SHEET NAME
KETRA N3 TO
SHEET
1 1
OF