Martinelli CULLA PRIMONIDO Mode D'emploi page 26

Instructions for use
Car Kit
How to fit the safety harness
IMPORTANT: during car travel, our mattress with a
3-point harness can be used.
IMPORTANT: In vehicles, always keep the backrest in
the horizontal position.
1 Unbutton the hood and foot muff (if present) completely
(fig_a) and remove them both (fig_b). Raise the backrest and
pull out the mattress (fig_c). Open the two zips and remove
the inner lining (fig_d).
2 Insert the 3 polystyrene sections inside the Culla Primonido,
and position them as shown in the figure.
WARNING: every piece must be inserted in its position
and cannot be replaced by another. Do not force the
pieces into place to avoid breaking the polystyrene.
3 Place the inner lining back into position, fitting the base over
the backrest.
4 Insert the mattress, which comes with 3 belt openings, and
fit it over the backrest.
5 3-POINT SAFETY HARNESS: Pass the leg divider straps
through the slot in the mattress pad (fig_a) and the slots
in the shell (fig_b) so that they come out on the other side
(fig_c).
6 Place the straps side by side so as to be able to fasten
them correctly to the shell (fig_a)
Thread the two ends of the straps into the slots in the
mattress and the shell (fig_b).
7 Hook them onto the clips on the back of the shell, as
shown in the figure.
8 Straps correctly fastened under the shell (fig_a)
To finish fastening the straps, overlap the tongues (fig_b)
and insert them into the crotch strap buckle until you hear
it click (fig_c).
Attachment in vehicles with safety belts
ATTACHING THE BASSINET UNIT IN VEHICLES: It is possible
to install the bassinet unit in cars if there are 3 rear seats
with 3 safety belts. The central one can be 3-point or a lap
belt.
We recommend positioning the bassinet unit on the
vehicle's rear seats with the end for the child's head above
the central seat.
9 Car bassinet unit fitted in a vehicle with a lap belt.
10 Car bassinet unit fitted in a vehicle with a 3-point belt.
11 The Car bassinet unit can also be positioned in the centre
of a 3-person rear seat, using the two outer safety belts
(fig_a). It cannot be positioned as in fig_b because it can
only be secured in vehicles using safety belts that come
from opposite sides.
12 Position of the Car bassinet unit on a 2-person rear seat.
The Car bassinet unit can be positioned with the child's
feet on either side of the vehicle. If the seat of the vehicle
inclines, towels can be used to provide a horizontal surface.
13 Take the rear seat belt, fold it as shown in the figure
(arrow_a) and insert it in the slot of the car kit's metal
fastener (arrow_b).
14 Insert the red lever on the metal fastener of the car kit
inside the folded belt (arrow_c).
Move the metal fastener as near as possible to the seat in
order to enable it to be fastened to the Carrycot (arrow_d).
15 Hook the car kit connector to the ring on the Carrycot and
pull firmly on the belt to ensure the Carrycot fits as well as
possible to the seat.
Repeat the same operations on the other side of the
Carrycot.
16 Car Carrycot installed in the car.
17 UNFASTENING THE CARRYCOT FROM THE CAR:
press the control button on the connector to loosen the
belts, as shown in the figure. Unhook the fastener of the
car kit connector from the ring on the Carrycot.
IMPORTANT: the car kit can remain fastened to the
seat belts of your car. The car kit fastener can easily be
attached to or removed from the ring on the Carrycot
(point 13).
IMPORTANT: do not leave the car kit fastened onto
the vehicle's safety belt when this is being used by an
adult.
How to put the child in the Car bassinet unit
18 3-POINT SAFETY HARNESS: loosen the straps by pressing
on the buckle (fig_a) and pulling them (fig_b).
Repeat the operation for both straps.
19 Press the red button (fig_a) and release the straps from the
leg divider (fig_b).
26