Martinelli CULLA PRIMONIDO Mode D'emploi page 24

5 The straps can be used to fasten the foot muff to the hood,
so as to protect the child even more against the elements.
Unfasten the sides of the foot muff, unfold it upwards and
fasten it to the hood with the straps.
6 The hood comes with a mesh insert so that the baby can
be seen from any position. Pull the zippers as shown in the
picture and pull the hood further, to reveal the mesh insert.
7 BACKREST ADJUSTMENT: pull the handle outwards and
rotate it clockwise to raise the backrest or anticlockwise to
lower it.
8 FOUR SEASONS SYSTEM: as shown in the figure, it is
possible to adjust the product's air circulation from the
base in order to prevent condensation.
Move the lever to blue for a cool, well-ventilated
environment (summer), or to red to limit the intake of air
(winter).
9 CARRY HANDLE: this is built into the hood. To carry the
bassinet, lift the hood (if lowered) until it clicks and hold
the handle placed above it.
_ Before lifting the bassinet, ensure the built-in hood is
correctly fastened.
_ Before lifting the bassinet, make sure the hood is in the
correct position for transport.
_ Before unfastening and lifting the bassinet from the frame,
adjust the backrest to its lowest position (figure 8).
GANCIOMATIC SYSTEM
10 The Ganciomatic System enables you to fasten the bassinet
quickly and easily, with one simple operation, to the
Ganciomatic base of the Bassinet Stand and the Classic
Chassis (purchased separately).
To attach the pram, put it on the chassis and press with
both hands until it clicks into place.
Always apply the brakes on the chassis before attaching
and removing the pram.
IMPORTANT: Check that the pram is properly attached.
11 To release it, press the lever under the bassinet and lift it.
12 REMOVING THE LINING: To remove the lining of the hood,
unfasten the 6 buttons on the lower profile.
13 Press the buttons on the two fasteners and remove the
hood.
14 Pull out the flap of fabric under the handle of the hood and
pull out the two rigid supports.
15 Raise the backrest (fig_a) to make it easier to remove the
mattress (fig_b).
16 Unfasten the 6 buttons on the outside of the bassinet and
remove the inner lining.
17 Finally, unfasten the 10 elastic bands on the bottom of
the bassinet and the other 4 positioned close to the hood
fasteners, and remove the outer lining.
18 To replace the lining of the bassinet, do the opposite. While
replacing the outer lining, make sure to slip the outer rings
into the right slots.
19 When placing the lining on the hood, ensure you insert the
rigid supports correctly. Insert the tube bearing the carry
handle into the hood's front slot, ensuring the handle is
centered correctly (fig_a). Pull the flap of fabric out from
the opening on the hood (fig_b) and slide it under the
handle (fig_c).
20 Finally, slip the second metal support into the hood's inner
slot.
21 Fasten the hood to the appropriate supports and fasten
the 6 buttons.
KIT AUTO
Product characteristics
Culla Primonido, Group 0, "Universal"
category
• The Car bassinet unit is approved under regulation UN ECE
R44/04 for children weighing from 0-10 kg. It is suitable for
installation on the majority of vehicle seats, but not all.
• The Car bassinet unit can be properly installed if the
vehicle's use and maintenance manual states that it is
compatible with "Universal" Group 0 restraint systems.
• The Car bassinet unit is classified as "Universal" in
compliance with stricter approval criteria than previous
models that do not have this label.
• The device can only be used on vehicles with 2 or 3 rear
seats fitted with 2- or 3-point safety belts, approved in
compliance with UN ECE R16 or equivalent regulations.
• For any questions or further information on installing
the Car bassinet unit in specific vehicles, contact the
manufacturer or the retailer.
24