Publicité
Les langues disponibles
Les langues disponibles
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don't cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
1. CHANNEL OUTPUTS: Each channel output has its own output socket to connect any resistive and/or
inductive projector(s) or small light effects.
2. CHANNEL FUSES: Each channel is equipped with a fuse and "blown fuse" detector. The detector lights
up when the channel fuse is blown. Always replace the blown fuse with a fuse that has the same
characteristics! (250V/8A).
IMPORTANT NOTE: It's very important to know that the maximum load for each channel is rated at 8A or
1850Watts. However the total load for all 4 channels may not exceed 20A or 4600Watts!
3. POWER INPUT: mains input, equipped with a Neutrik Powercon
and the projectors (and/or light effects) are properly connected to the channel output sockets (1) before
you connect an earthed mains cable to this input. The maximum total load is 20A or 4600Watts.
4. INPUT FUSE: This is an automatic circuit breaker. When the fuse is blown, first locate and solve the
problem that caused the fuse to blow. When the problem is solved, simply push the button to reset the
circuit breaker.
5. DMX OUTPUT: 3pin female XLR-connector used to connect the DB-46 with the next unit in the DMX
chain.
6. DMX INPUT: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller.
7. STAND ADAPTER: used to put the DB-46 easily on top of a light stand. Two different stand adapters
are included (also see number 9 for more information):
35mm adapter: to be used on stands with a standard 35mm top section.
28mm TV-Spigot: to be used on stands equipped with a TV-spigot adapter on top.
®
, make sure the local voltage is 230Vac
8. SLIDING MECHANISM: used to distribute your projectors evenly over the DB-46. Also see number 9 for
more information.
9. END CAP: To install the bolts/nuts (needed to fix the projectors) and stand adapter you have to remove
this end cap on one side of the unit: simply unscrew the 4 screws remove the cap put the nuts/bolts
and/or stand adapter in the sliding rail put the cap back in place fix the 4 screws done!
10. CONTROL PANEL: multifunctional display + 4 buttons to navigate the setup menu. See the numbers
below.
11. DISPLAY: shows the information related to the selected function or working mode. The left digit shows
the channel number, the 3 other digits show the channel status:
In the address menu: channel address is shown, ranging from 001 to 512
In the mode menu: working mode is shown. ("d" = dimmer mode * "S" = switch mode)
In the dim menu and standard display: channel output status is shown.
Channel in dimmer mode: dimmer percentage, ranging from 0% to 100%
Channel in switch mode: "oN" = output 100% * "oFF" = output 0%
12. MENU BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
Browse the main menu: Press the MENU button together with the UP/DOWN buttons.
Return to the main menu: Press the MENU button to return to the main menu. (escape function)
Display blackout function: Press the MENU button together with the ENTER button to switch the
display on/off.
13. DOWN BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
Browse the main menu: Press the MENU button together with the UP/DOWN buttons.
In the address menu: Press the DOWN button to lower the DMX address of the selected channel.
(press the button for a longer time to increase the speed)
In the mode menu: Press the DOWN button to put the selected channel in switch mode.
In the dim menu: Press the DOWN button to lower the dimmer value (0~100%) when the selected
channel is in dimmer mode. (press the button for a longer time to increase the speed). When the
selected channel is set to switch mode, you can turn the output off.
14. UP BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
Browse the main menu: Press the MENU button together with the UP/DOWN buttons.
In the address menu: Press the UP button to increase the DMX address of the selected channel.
(press the button for a longer time to increase the speed)
In the mode menu: Press the UP button to put the selected channel in dimmer mode.
In the dim menu: Press the UP button to increase the dimmer value (0~100%) when the selected
channel is in dimmer mode. (press the button for a longer time to increase the speed). When the
selected channel is set to switch mode, you can turn the output on.
15. ENTER BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
In the main menu: Press the ENTER button to select the desired sub menu.
In a sub menu: Press the ENTER button to browse through the 4 channels.
Display blackout function: Press the MENU button together with the ENTER button to switch the
display on/off.
16. DMX PRESENT LED: this LED indicates if the unit receives a DMX-signal on the DMX-input(n°6):
LED is on: no DMX-signal detected on the input.
LED is blinking: DMX-signal detected on the input
Publicité
