Publicité
Les langues disponibles
Les langues disponibles
Интернет-магазин «Мистер Климат»
• Do not pull the power cable over sharp edges or allow it to become
jammed.
• Never remove the plug from the socket by pulling at the power cable and
never remove it with wet hands.
• Do not use this humidifier in close proximity to a bath tub, shower or
swimming pool (always ensure a minimum distance of 3m). Always place
the device in a position where it cannot be reached by anyone in the bath
tub.
• Do not set up the device near a source of heat. Do not subject the power
cable to direct heat (such as heat from hot oven hobs, naked flames, hot
irons or heating furnaces). Keep the power cable away from oil.
• Do not position the device directly next to walls, curtains or furniture.
• Ensure that the device is stable during operation and that no-one can trip
over the power cable.
• The device is not splash-proof.
• Do not store or use the device outdoors.
• Store the device in a dry place, out of the reach of children (in its box).
• Do not add anything to the water (fragrances, essential oils or water
fresheners).
DESCRIPTION
1. Power cable for power supply
2. Mist cap
3. Transparent water tank
4. Filter cartridge
5. Water tank cover
6. Main base
7. Control panel and Display
8. Ionic Silver Cube
(optional)
TM
9. Mist Cap guide
10. Handel
11. «On/Off» Switch button
12. «Humidity» button
13. «Output» button
14. «Warm Mist» button
15. «Night Mode» button
16. «Auto Mode» button
OPERATION
Please note: never transport the device with a full water tank. Possible ha-
zards:
• too much water from water tank comes into the Main Base (6), this over
loaded water level will cause dramatic reduction of mist output of the
device.
• water can easily come out from the Main Base (6).
• the water tank can fall off from the Main Base (6) and get damaged due
to the heavy weight from the water (and water can leak on to the floor).
1. For this reason, Main Base (6) of the Stadler Form Poseidon humidifier
should be placed first with empty Water Tank (3) in a suitable location.
2. When the device is in the desired location: Fill Water Tank (3) with fresh
water and screw the Tank Cover (5) back on firmly and check that it is
sealed properly. Place Water Tank on base. Plug Power Cable (1) into
the power socket. In the model with Filter Cartridge (4): do not take off
the Filter Cartridge from the Tank Cover when opening and filling water
for the tank.
3. Switch on the device by pressing the On/Off switch (11) on the Con-
trol English Panel (7), the control display appears blue. The Mist Cap (2)
can be turned 360° or used bi-directional to have an even distribution
of moisture.
4. The desired air humidity level can be selected by pressing the Humidifity
button (12) on the Control Panal. The device will be shut off automati-
cally when the room humidity reaches the given level. On the Display
panel (7), it shows the current humidity level in the room. By pressing the
Humidifity button (12), you will be able to set the desired humidifity from
30%, 35%, 40% ... 75% and «continous» model. Release the button at
your desired humidifity level or at continous model, the unit is set and the
display will switch to show the actual room humidity level again. Note:
on «continous» the unit will NOT turn off automatically.
Caution: the device will not be switched on if the humidity level is set too
low.
5. Pressing the Output button (13) on the control panel, you can change
the volume of output mist from Level 1 to Level 3 (shown on the display
panel).
6. «Warm Mist» button (14): a heater can be switched on by pressing this
button. This heater will heat up the water to 80 C° before it enters into
the mist generation chamber. By this pre-heating function, the tempera-
ture of the output mist will reach 40 C°, which will not cause the room
temperature to drop when mist evaporates. A LED light on top the dis-
play panel will be switched on when this pre-heating function is turned
on. Press this button again to switch off this function, and the LED light
will be switched off.
7. «Night Mode» button (15): Pressing this button, the device is switched
to «night mode» with dim LED light. Press again, the device is back to
normal light mode. During this mode, the relative humidity will be kept
at a comfort level of 50%.
8. «Auto Mode» button (16): This button can set the humidifity level at 50%
and the ventilator works at the optimal level 1. By pressing this button,
the previous humidity level set by «Humidity» button will be canceled.
9. «No water» alarm light: At the lower part of the display panel, there
is red LED alarm light. This light will on when there is no water or not
enough water in the mist generating chamber. When this light is on, you
should switch off the unit buy press the «On/Off Switch» and refill the
www.mrklimat.ru
Тел.: 8-800-5555-710
Publicité
