Table des Matières
Publicité
DC 50 PLUS
in rotation and make sure that you keep anything
that could be trapped in the operating machine,
such as loose hair and clothing, away. Keep your
hands away from the machining area when oper-
ating the machine.
Work pieces and tools can ricochet and lead to
injury and property damage. Make sure that the
machine and tools are always in good condition.
The suction force of the machine is generated
by a high speed fan that can be hazardous when
operating. Periodically check the inlet of the ma-
chine for blockage, but make sure the machine is
first disconnected from mains and that the fan has
come to a complete stop.
NOISE AND VIBRATION HAZARDS
The noise levels shown in these instructions are
the maximum levels for use of the machine. Insuf-
ficient maintenance has a significant impact on
vibration and noise emissions. Consequently, it
is necessary to take preventive steps to eliminate
possible damage due to high levels of noise and
stress from vibration. Maintain the machine well,
wear ear protection devices, anti-vibration gloves
and take breaks while working.
WORKING AREA HAZARDS
Thoroughly inspect the whole work area and use
a rake or yard brush to manually loosen debris
and remove anything that could be a hazardous
source to you or cause damage to the machine.
Keep work area clean and tidy. Do not operate the
machine in wet environment conditions or when
the machine itself is wet. Keep the machine away
from flammable material. Check that there are no
bystanders, animal or items that could be dam-
aged within the machine's range of action.
Operate only in well ventilated areas. Chips and
saw dust can be a health hazard when inhaled
or when in contact with the eyes. Always wear
appropriate half-mask respirator and protective
goggles, when working with such materials and
use a dust extraction device.
Work only in daylight, or with suitable artificial
light, in good visibility conditions. Try not to cause
any noise disturbance, by only using this machine
at reasonable times of the day.
Take on a firm and well-balanced position. Where
possible, avoid working on wet, slippery ground
or in any case on uneven or steep ground that
does not guarantee stability for the operator.
Storing of tools that are not in use should be done
in a dry and safe place away from the operating
machine and out of the reach of children.
REMAINING HAZARDS
The machine was built using modern technology
and in accordance with recognized safety rules.
Even when all safety measures are in place, some
remaining hazards, which are not yet evident, may
be present. The operator should use common
sense and take necessary precautions to avoid risk
due to remaining hazards.
PRODUCT SPECIFICATIONS
INTENDED USE
This machine is designed and manufactured for
suction of wood dust and chips or similar materi-
als, e.g. woodworking. It is not designed for heavy
commercial use.
Any other use differing from the above-mentio-
ned ones could be hazardous, harm people and/or
damage things and the machine itself.
IMPROPER USE
The machine must not be used for machining ha-
zardous materials, e.g. accumulation of inflam-
mable or explosive products, stones, metal and
any other object that could be dangerous to the
machine itself as well as the operator, bystanders,
animals or property.
Other examples of improper use may include, but
are not limited, to operation of the machine:
Without the original accessories supplied by the
f
manufacturer.
With original accessories but in a way not in accor-
f
dance to the instructions.
Without original spare parts.
f
With unauthorized modifications.
f
NOTE:
According to the applicable product liability laws,
the manufacturer of the device does not assume lia-
bility for damages to the product or damages caused
by the product that occurs due to:
Improper handling no complied with the operat-
f
ing instructions.
Repairs by third parties and not by authorized ser-
f
vice technicians.
Installation of non-original spare parts.
f
Non-intended use.
f
Electrical system breakdown due to power of the
f
machine in a manner not compliant with the elec-
tric and VDE and DIN regulations.
TECHNICAL DATA
Article Number
Model
Rated voltage
Rated frequency
Power
Fan diameter
Pressure
Airflow
Container volume
Micron rating
Suction hose diameter
Cable (VDE)
Dimensions (L x W x H)
English |
7
45 995
DC 50 PLUS
V
230-240
Hz
50
W
1.200
mm
130
Pa
2.500
m
/hr
183
3
L
50
0,5
mm
100
m
5
mm 420 x 420 x 730
www.ffgroup-tools.com
Publicité
Table des Matières
