Publicité
Les langues disponibles
Les langues disponibles
Installation and Operating Instructions
1/3" Board Camera, Day & Night
VKC-1327A/VAR49
1. Safety Instructions
• Read these safety instructions and the operation manual first before you
install and commission the camera.
• Keep the manual in a safe place for later reference.
• P rotect your camera from contamination with water and humidity to prevent it
from permanent damage. Never switch the camera on when it gets wet. Have it
checked at an authorized service center in this case.
• Never operate the camera outside of the specifications as this may prevent
the camera functioning.
• D o not operate the cameras beyond their specified temperature, humidity or
power ratings. Operate the camera only at a temperature range of -10°C to
+50°C and at a humidity of max. 90%.
• To disconnect the power cord of the unit, pull it out by the plug.
Never pull the cord itself.
• P ay attention when laying the connection cable and observe that the cable is
not subject to heavy loads, kinks, or damage and no moisture can get in.
• T he warranty becomes void if repairs are undertaken by unauthorized persons.
Do not open the camera housing.
• Never point the camera towards the sun with the aperture open.
This can destroy the sensor.
• I nstallation, maintenance and repair have to be carried out only by authorized
service centers. Before opening the cover disconnect the unit from mains input.
• The fitter is responsible for the system of protection being followed in accor-
dance with the technical data, e.g. by sealing of the cable outlet with silicone.
• Contact your local dealer in case of malfunction.
• Only use original parts and original accessories from Videor E. Hartig GmbH.
• Do not use strong or abrasive detergents when cleaning the dome.
Use a dry cloth to clean the dome surface.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
• During assembly, care must be taken to ensure that existing seals are
correctly inserted and are not displaced as a result of assembly.
You must not continue to use damaged seals.
NOTE: This is a class A digital device. This digital device can cause harmful
interference in a residential area; in this case the user may be
required to take appropriate corrective action at his/her own expense.
2. General Description
• 1/3" Day/Night CCD Board Camera, 38x38mm
• Resolution of 540 Horizontal Lines
• Sensitivity of 0.15Lux (AGC Turbo and B&W)
• Built-in Lens F1.2/3.8-9.5mm with DC Iris Control
• Removable IR Cut Filter (ICR)
• Digital Signal Processing (DSP)
• High Speed Shutter Control (ESC)
• Backlight Compensation (BLC)
• Automatic White Balance (ATW)
• Supply Voltage: 12VDC/24VAC
3. Part Names
1
2
3
4
Front view
(1) Focus adjustment knob
(2) Iris level adjustment potentiometer
(3) Zoom adjustment knob
(4) Function switches (Piano switch)
4. Functional Descriptions and Adjustments
4.1 Focus adjustment knob (1)
Adjust the focus to get a sharp image and lock it by knob screw after finishing
adjustment.
If the camera is shooting a very bright object, use a proper ND filter to make the
iris full-open to achieve the best focus adjustment.
This step is recommended after finishing step 4.3.
4.2 Iris level adjustment potentiometer (2)
Adjust the iris level adjustment pot. to get the best video level on the monitor.
Iris level adjustment pot. works only when ELC/ALC switch is set to ALC.
This adjustment is recommended after steps 4.1 and 4.3.
4.3 Zoom adjustment knob (3)
Adjust the zoom knob to set the view angle and lock it by knob screw after
finishing adjustment.
4.4 Power/ Video Connector (6)
Plug the power/video cable to this connector.
4 Video Out
3 GND
2 AC 24V
1 AC 24V
4.5 Vertical phase adjustment potentiometer (5)
Adjust the vertical phase adj. pot to synchronize the vertical phase to other
cameras. This adjustment works only when camera works in line-lock mode with
24VAC supply and LL position of Int/LL switch. If it is impossible to match the
synchronization, exchange the AC power connections and try the adjustment
again.
6
7
5
Rear view
(5) Vertical phase adjustment
potentiometer
(6) Power/video connector
Publicité
