Speaka Professional 1229080 Notice D'emploi page 3

G
O P E R A T I N G I N T R U C T I O N S
HDMI Audio Extractor
Item no. 1229080
Intended use
The product is used to uncouple an audio signal from an HDMI signal. The audio signal is then
available through a stereo cinch output or an optical digital output. The HDMI signal is passed
through for further use.
The wall plug transformer enclosed is used to supply the power.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Package Contents
• Audio extractor
• Wall plug transformer
• Operating instructions
Safety Instructions
D amages due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
• The unauthorised conversion and/or modification of the product is not permitted for
safety and approval reasons (CE). Never disassemble the product.
• This product is not a toy. Devices operated using mains voltages should not be
used by children. Therefore, be especially careful when children are around.
Use the product where it is out of the reach of children.
• The product is intended for use in dry, indoor locations only. No part of the product
should become damp or wet; never handle it if your hands are wet!
Wall plug transformers pose the potential risk of a fatal electric shock!
• The design of the wall plug transformer complies with Protection Class II. Use only
a standard mains socket as the power source for the wall plug transformer.
The mains socket into which the wall plug transformer is plugged must be easily
accessible.
• Use only the wall plug transformer supplied to power the audio extractor.
• Do not pull the wall plug transformer from the mains socket by pulling on the cable.
Hold it on the sides of the casing and pull it out of the mains socket.
• Do not touch any wall plug transformer that shows signs of damage; there is a
danger to life from electric shock!
First, switch off the mains voltage to the socket to which the wall plug transformer
is connected (switch off at the corresponding circuit breaker or remove the safety
fuse or switch off at the corresponding RCD protective switch, so that the socket is
fully disconnected).
You can then unplug the wall plug transformer from the mains socket. Dispose of
the faulty wall plug transformer in an environmentally friendly way, do not use it any
more. Replace it with a wall plug transformer of the same design.
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
falls, even from a low height.
Controls
Version 09/14
1 LED "Link" for HDMI connection
2 Power LED
3 ON-OFF button, to switch on and off
4 Low-voltage jack for mains/power supply
5 Sliding switch to select audio modes
6 Analogue stereo output (right channel)
7 Analogue stereo output (left channel)
8 Optical digital output
9 HDMI output (passed through HDMI signal)
10 HDMI input
Connection and commissioning
a) Setup and Connection
• Connect the HDMI input (10) via a suitable HDMI-capable cable to the HDMI output of a
playback device such as a Blu-ray player, game console, etc.
• If you want the HDMI signal to pass through a TV, for example, connect the HDMI output (9)
to the HDMI input on your TV.
• The two RCA sockets deliver the analogue stereo audio signal (red socket = right channel,
white socket = left channel). The sliding switch (5) must be on position "2CH LPCM".
• The TOSLINK connector (8) carries the digital optical audio signal. Here, the sliding switch
(5) must be either on "Bitstream" or on "2CH LPCM".
• Connect the analogue stereo output (6/7) or the optical digital output (8) to the corresponding
input of an amplifier for example.
• Connect the circular low voltage plug of the wall plug transformer provided to the correspond-
ing socket (4) of the audio extractor.
• Plug the wall plug transformer into a mains socket.
• Place the audio extractor on a solid, horizontal surface. •
furniture by using an appropriate underlay to avoid scratches and pressure marks.
b) Turning the audio extractor on/off
• Press the "ON/OFF" button (3) on the front of the audio extractor to switch it on or off.
• The Power LED (2) will go on, when the audio extractor is switched on.
• The "Link" LED (1) will go on, when the HDMI connection between HDMI input and HDMI
output has been established.
c) Selecting audio output or audio signal
The sliding switch (5) controls the EDID, so that the playback device (e.g. a Blu-ray player
or games console) makes the corresponding audio signal available (LPCM7.1, Dolby 5.1
stereo / 2 channel LPCM).
However, the audio signal that will be available is subject to the capabilities of the signal source
such as a Blu-ray player, and it naturally also depends on the available audio channel on a
Blu-ray, for example.
Depending on the position of the switch, the audio signal is passed through the the different
outputs of the audio extractor.
• Switch on "2CH LPCM"
All outputs (stereo analogue output, digital optical output and HDMI output) deliver a 2-chan-
nel audio signal (stereo audio signal).
• Switch position "Bitstream"
The digital optical output and the HDMI output deliver at most a Dolby digital 5.1 signal,
depending on the signal source. The analogue stereo output is functionless.
Protect the surfaces of valuable