Bresser 3810000 Manuel D'instructions page 7

OPERATION
1) How to provide power for DC12V appliances (such as head lamp, fan)
with this product?
The 5.5mm 12V DC output is plug and play. Plug your appliances to the
DC output port to gain power. DC output rated Current: 10A, Max output
Current <15A.
Note:
Please confirm whether your DC12V appliance support charging with
5.5mm DC header interface (The diameter of the DC Port of the Product
is: 5.5mm), otherwise it is unable to connect with the DC output.
[ RIGHT ]
Note:
The 12V DC output voltage is range between 9V~12.6V, maximum output
current is 15A. DC output voltage drops while battery capacity drops due
to chemical characteristics of the battery. If your appliance is not built-in
input voltage stabilizing function, it may shutdown when input voltage
is too low, please unplug your device from the unit in time. And please
charge the unit in time.
Short-circuit/Overpower Protection:
If the DC output is short-circuited or overpowered (Load(s) power>150W),
the unit will shutdown to protect itself. Please clear the problem and
recharge the unit to recover from protection mode.
2) How to provide power for AC appliances with this product?
Connect the power cable plug of the electrical appliance to the AC outlet
of the product, switch on the power button and the unit will start providing
power to your appliances.
WARNING! The AC outlets, AC voltage and frequency are different accor-
ding to different countries ; please carefully check whether the product
specifications are consistent with the appliance specifications before use,
otherwise it can lead to dangerous situations.
[ RIGHT ]
Limited Appliance Wattage <100W, Lamp,
Electric Fan, TV, etc. AC will shutdown when it's
short circuited or power overloaded.
Remove the device and the unit will recover from
short-circuit or overpower protection in a few
seconds. Then, press the AC output button to
When the AC port is not in use, turn it off to conserve power.
Short-circuit/Overpower Protection: If the AC output is short-circuited
or overpowered (Load(s) power>100W), the unit will shutdown AC output
to protect itself. Please clear the problem and re-press the AC button for
AC output.
USB C
Manual_3810000_Mobile-Power-Supply_de-en-fr-es_BRESSER_v052021a.indd 7 Manual_3810000_Mobile-Power-Supply_de-en-fr-es_BRESSER_v052021a.indd 7
5.5mm DC12V for Fan
or LED lights
or charge car kits via DC to Cigarette
Lighter Connector
Support for 5.5mm DC12V car kits
with DC-Cigarette Lighter Adapter,
such as Vacuum Cleaner, Inflation
Pump, Electric wrench, fridge, etc.
switch on AC output again.
Some devices, such as refrigerator, ice maker or a laser printer may require a
power surge to start work. The power surge could exceed 150W or even hig-
her, this could cause overpower protection with this unit. Please remove the
devices and consult with the device manufacturers for more information.
Please clear the problem and re-press the AC button for AC output.
3) How to provide power for USB(C) digital appliances with this product?
Connect the standard USB cable of digital appliance to the USB output of
the unit, press the " " to turn on USB output.
[ RIGHT ]
USB C
Note: Some smart devices, such as Bluetooth headphones and LED lights
require very small input current to charge, which could be less than 150mA.
The unit may fail to charge these kind of smart devices due to detection
current limitation by the USB output ports. On this occasion, user can press
the AC button " " to keep the USB port output running. Please turn off AC
output when the smart devices are fully charged to save power.
Quick Charge Output: This product supports Qualcomm QuickCharge 3.0
output, support 5V-9V / 2A max output for smartdevices which also sup-
port Qualcomm QuickCharge 3.0. The actual output voltage and current
depends on the actual smartdevices, it can be obtained by consulting the
smartdevice manufacturer.
4) How to use the flashlight
This unit is built with ultra bright LED flashlight. Press the "
to switch on flashlight and single press the button to switch to blink/SOS
mode, Press the button to switch off.
Warning! Do not point directly at the eyes of human in case of any damage
due to the strong light.
5) How to use the Led light panel
This unit is built with LED lightpanel. Press the "
lightpanel and single press the button to switch brightness, Press the but-
ton again to switch off.
USB C
Warning! Do not point directly at the eyes of human in case of any damage
due to the strong light.
6) How to charge the unit?
A.Charge through AC Wall Charger
Using the included AC Wall Charger, plug the unit into any wall outlet to
charge the unit. You will know the unit is charging when the blue LED bat-
tery indicators are blinking. The unit is fully charged when all battery indi-
cators stop blinking and remain solid. After the unit is fully charged, please
remove the AC wall charger in time.
[ LEFT ]
B.Charge from Solar panel
1. Place your solar panel where it will get as much direct sunlight as pos-
sible.
2. Plug the output of the solar panel into the input of the unit to start
charging.You will know the unit is charging when the blue LED Battery
" button
" button to switch on
AC Socket


AC Adapter (charger)
15V/2A
7
25.05.2021 14:17:21 25.05.2021 14:17:21