Zoeller Home Guard Max 503 Mode D'emploi page 2

Manufacturer warrants, to the purchaser and subsequent owner
during the warranty period, every new product to be free from
defects in material and workmanship under normal use and
service, when properly used and maintained, for a period of three
years from date of manufacture. Parts that fail within the warranty
period, that inspections determine to be defective in material or
workmanship, will be repaired, replaced or remanufactured at
Manufacturer's option, provided however, that by so doing we
will not be obligated to replace an entire assembly, the entire
mechanism or the complete unit. No allowance will be made
for shipping charges, damages, labor or other charges that may
occur due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for
any material or product that has been disassembled without prior
approval of Manufacturer, subjected to misuse, misapplication,
neglect, alteration, accident or act of nature; that has not
been installed, operated or maintained in accordance with
Manufacturer's installation instructions; that has been exposed to
outside substances including but not limited to the following: sand,
gravel, cement, mud, tar, hydrocarbons, hydrocarbon derivatives
(oil, gasoline, solvents, etc.), or other abrasive or corrosive
substances, wash towels or feminine sanitary products, etc. in
In those instances where damages are incurred as a result of an alleged pump failure, the homeowner must
1. The system is designed for installation in sumps with minimum
diameter of 18" and depth of 22". For smaller applications,
consult factory.
2. Remove all debris from the pit before installation.
3. Be sure that the pump is clamped securely to the primary
pump discharge pipe and that the two pumps do not interfere
with each other.
4. Install a serviceable check valve in the discharge line.
1. DO read all installation materials supplied with the pump.
2. DO inspect unit for any visible damage caused by shipping.
Contact dealer if unit appears to be damaged.
3. DO clean all debris from the pit before installation.
4. DO install a union check valve (see STEP 3) in the
discharge line. DO NOT use a discharge pipe smaller than
the recommended pump discharge sizes.
5. DO install a filter or strainer in the water supply line before the
pump to prevent small particles from clogging the operating
valve.
6. DO test the pump immediately after installation to be sure
that the system is working properly.
7. DO review all applicable local and national codes and verify
that the installation conforms to each of them.
LIMITED WARRANTY
retain possession of the pump for investigation purposes.
Helpful Hints For Easy Installation
Do's And Don'ts For Installing A Unit
© Copyright 2015 Zoeller
all pumping applications. The warranty set out in the paragraph
above is in lieu of all other warranties expressed or implied;
and we do not authorize any representative or other person to
assume for us any other liability in connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Louisville,
Kentucky 40211, Attention: Customer Support Department to
obtain any needed repair or replacement of part(s) or additional
information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR
SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES OR
BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND
ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED
TO THE DURATION OF THE EXPRESSED WARRANTY.
Some states do not allow limitations on the duration of an implied
warranty, so the above limitation may not apply to you. Some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion
may not apply to you.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
5. Install a filter or strainer in the water supply line before the
pump. Size the filter/strainer properly to minimize pressure
drop, while retaining particles 0.020" (0.5 mm) in diameter
and larger.
6. Test the unit immediately after installation. Refer to STEP 5.
7. Check the Float ON/OFF levels per STEP 2 of the instructions.
8. Keep the model number, date code, and installation
instructions in a convenient location for future reference.
8. DO NOT use the Home Guard
DO NOT use the Home Guard
sewage, effluent, or water with debris in it.
9. DO NOT use a garden hose. Garden hose is not designed
to hold municipal pressure indefinitely and could leak or
burst causing flooding. The Home Guard
permanent piping method such as copper, PEX, or CPVC.
10. DO install the Home Guard
supply line.
11. DO install a union or other quick-disconnect fitting to make
the pump accessible for servicing on both the water supply
and discharge piping.
12. DO install a dedicated shut-off valve on the water supply line
within 6 ft. (1.8 m) of the Home Guard
Co. All rights reserved.
®
2
Max with hot water.
®
Max to remove wastewater,
®
Max requires a
®
Max pump with only a ¾"
®
Max.
®