Stanley FME190 Traduction Des Instructions Initiales page 6

ENGLISH
Labels on tool
The following pictograms along with the date code are shown
on the tool:
:
Warning! To reduce the risk of injury, the user
O
must read the instruction manual.
Wear safety glasses or goggles.
N
Wear ear protection.
6
Wear a dust mask.
Wear gloves when handling blades.
Electrical safety
#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Inspect tool cords periodically. If the supply cord is
u
damaged, it must be replaced by the manufacturer or an
authorised Stanley Fat Max Service Centre in order to
avoid a hazard.
Voltage drops
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected. If the system impedance of the power supply is
lower than 0.34 Ω, disturbances are unlikely to occur.
Using an extension cable
Always use an approved extension cable suitable for the
u
power input of this tool (see technical data). Before use,
inspect the extension cable for signs of damage, wear and
ageing.
Replace the extension cable if damaged or defective.
u
When using a cable reel, always unwind the cable
completely. Use of an extension cable not suitable for the
power input of the tool or which is damaged or defective
may result in a risk of fire and electric shock.
Features
This tool includes some or all of the following features.
1. Air vents
2. Handle (left & right)
3. Socket
4. Shaft
5. Stirrer
6
(Original instructions)
6. lock-on button
7. Variable speed switch
8. Power cord with plug
9. Mounting spanner 22mm (x 2)
Assembly.
Unpacking.
Unpack all parts and lay them on a flat, stable surface.
u
Remove all packing materials and shipping devices, if
u
applicable.
Make sure the delivery contents are complete and free
u
of any damage. If you find that parts are missing or show
damage do not use the product but contact your dealer.
Using an incomplete or damaged product represents a
hazard to people and property.
Ensure that you have all the accessories and tools needed
u
for assembly and operation. This also includes suitable
personal protective equipment.
Warning! The product and the packaging are not children's
toys! Children must not play with plastic bags, sheets and
small parts! There is a danger of choking and suffocation!
Setup
Warning! The product must be fully assembled before
operation! Do not use a product that is only partly assembled
or assembled with damaged parts! Follow the assembly
instructions step-by-step and use the pictures provided as a
visual guide to easily assemble the product! Do not connect
the product to power supply before it is completely assembled!
Stirrer
Warning! Stirrers are available in different types and with
different shape and diameters. Always use the correct
stirrer according to the intended use! Observe the technical
requirements of this product (see section "Technical
specifications") when purchasing and using stirrer! Stirrer
becomes hot during use! Handle them carefully! Wear
protective gloves when handling stirrer in order to avoid
injuries like burns and cuts!
Attaching (Fig.A, Fig.B, Fig.C, Fig.D)
Align the stirrer (5) with the shaft (4). Screw the stirrer (5)
u
clockwise onto the lower end of the shaft (4) (Fig. A).
Lock the welded nut of the shaft (4) with one mounting
u
spanner (9) and secure the stirrer (5) clockwise with the
other (9) gripping the welded nut (Fig. B).
Note! Tighten the connection hand tight at first, before using
the spanners.
Align the shaft (4) with the socket (3). Screw the shaft end
u
with welded nut clockwise into the socket (3) (Fig. C).
Lock the socket (3) with one mounting spanner (9) and
u
secure the shaft (4) clockwise with another mounting
spanner (9) gripping the welded nut (Fig. D).