Renkforce M618X Mode D'emploi page 4

a) Wireless Connection Options
You can connect up to 4 devices (not at the same time).
LED Channel
B1 Bluetooth 1
B2 Bluetooth 2
B3 Bluetooth 3
OFF 2.4 GHz
• Toggle through bluetooth channels (B1-B3) and 2.4 GHz by pressing channel select (15).
- An LED (16) will flash then go off to indicate which channel has been selected.
- For the 2.4 GHz connection, the LED indicator light will turn off.
2.4 GHz Connection
Device ID "2.4G Wireless Mouse".
• Remove the 2.4 GHz USB receiver from the USB receiver (8) slot and connect it to an available USB port
on your computer.
• The operating system will automatically install any needed drivers.
• Press the channel select button (15) and select 2.4 GHz.
Bluetooth Connection
Refer to your computer operating system instructions for details about connecting to new
bluetooth devices.
Device ID: Bluetooth 3.0 "Vertical MS 3.0", Bluetooth 4.0 "Vertical MS 4.0".
To pair your mouse to your computer using Bluetooth:
• Press the channel select button (15) to choose a Bluetooth channel.
• Press and hold the channel select button until the LED channel indicator (16) blinks slowly.
• Your mouse will no be open for pairing with your computer for 120 seconds.
• Repeat the pairing process if the connection attempt is unsuccessful.
Mouse Driver Software
a) Install Software
Install the "Renkforce M618X Wireless Mouse" driver software for access to custom key and macro settings.
• Insert the driver installation disc into your computer disc drive.
• Select the "Renkforce M618X Wireless Mouse.exe" file on the driver CD.
• Follow the on-screen installation instructions to complete the installation process.
Run the "Renkforce M618X Wireless Mouse" software to access "Key Setting" and "Macro
Setting".
b) Key Setting
You can assign different functions or macros to standard mouse keys,
1 and 2, you must first re-assign them to keys 3, 4, or 5.
Key Setting
Click, Menu, Scrolling, IE Forward,
IE Backward, Scroll Up, Scroll Down,
Assign a shortcut
Double click
Three click
Button off
Select a macro
Multimedia > sub-menu
Windows > sub-menu
Basic function > sub-menu
Advanced function > sub-menu
• Run the "Renkforce M618X Wireless Mouse" program on your computer.
• Select a mouse key (1-5).
Hovering your mouse over a key setting will highlight the related mouse key in the image.
• Choose a new key setting from the dropdown menu.
• Select "Apply" to save changes or select "OK" to exit without saving.
Windows Pointer Speed
®
• Adjust the slider to increase or decrease the pointer speed.
• Select or deselect "Enhance Pointer Precision".
This changes the sensitivity of the mouse depending on the rate you are moving it, and can enhance
precision.
c) Macro Settings
You can record, edit, delete and load macros through "Macro Settings".
Icon Name Description
New Macro Add new macro.
Delete Delete entire macro or single command lines.
"Load" / "Save" Load a new macro or save an edited one.
Up / down Select the next item above or below.
"Edit Macro" Select command you would like to update then select
but before changing keys
Description
Re-assign standard key functions.
Ctrl, Shift, Alt, Win
Assign 2x clicks for each single press
Assign 3x clicks for each single press
Deactivate a function key
Assign any previously saved macros.
See section c) "Macro Settings" for further information.
Assign various multimedia functions
Assign various Windows functions
®
Assign some commonly used functions
Assign various advanced functions
"Edit
Record New Macro
• Select + then rename it under the "Macro Name"
• Set the desired interval between commands.
- "Record Delay" the delay between commands will be recorded as entered in real time.
- "Default Delay" uses a predefined interval for the delay, expressed in milliseconds (ms)
- "No Delay" omits all pauses between keystrokes and button presses.
• Press "Start Record" to begin recording the macro.
• Enter a sequence of mouse and key strokes.
• Press "Stop Record".
Edit a Macro
• Select a saved macro from the "Macro List"
• Select a command you wish to modify from the list then select:
- to delete.
- to edit.
• Scroll down to the last command and
save any changes.
d) Factory Default Settings
Run the "Renkforce M618X Wireless Mouse" program on your computer, then select "Reset" to:
• Restore all key settings to standard mouse keys.
• Delete all recorded macros.
• Restore all light settings
Power Saving
If not using the mouse for an extended time, slide the power switch (9) to the OFF position.
• If left untouched for more than a 1 minute the mouse will enter energy saving mode. The breathing light
will go off.
• Touch any key to reactivate the mouse.
• Turn the LED breathing light off to extend the battery life. See section "LED Breathing Light".
LED Breathing Light
You can change the colour of the breathing light or turn it off completely.
• Press and hold the DPI button (1) and cycle through the scrolling wheel (2) one notch at a time to choose
a colour.
• To turn the breathing light off, scroll through the colours until the LED light turns off.
Care and Cleaning
• Disconnect the product and turn the power off before cleaning.
• Check if the sensor on the bottom of the mouse is dirty.
• Do not immerse the product in water.
• Use a dry, lint-free cloth to clean the product.
• Do not use any abrasive or chemical cleaning materials.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines. You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical Data
Power supply ........................................ 5 V/DC, 500 mA via USB Type-C
Battery .................................................. 3.7 V 800 mAh LiPo
Current consumption ............................ ≤ 10-15 mA (active mode with LED on)
Battery life ............................................. LED on: approx. 2 weeks (2 hrs use per day)
Battery recharge time ........................... 2.5 - 3 hrs
Energy saving mode ............................. 1 min
Sampling rate ....................................... 600 / 1200 / 1600 / 3200 dpi
Mouse sensor ....................................... Optical
Connectivity ..........................................
Device ID .............................................. Bluetooth 3.0: Vertical MS 3.0
Cable length ......................................... 1.4 m
Design .................................................. Right-handed operation
Frequency ............................................. 2400 - 2479 MHz
Transmission power.............................. 0 dbm
Transmission distance .......................... <10 m
Radio equipment .................................. Class 1
System requirements ............................ Windows
Operating / storage conditions .............. 0 to +40 ºC, 0 – 90 % RH
Dimensions (W x H x D) ....................... 102 x 84 x 146 mm
Weight .................................................. 226 g
Macro".
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
dialog box.
or edit a current macro by pressing "Stop
start record to continue recording where you left off or click
TM
≤ 3 mA (energy saving mode)
Bluetooth 3.0 / 4.0 (3 channels)
2.4 GHz via USB receiver (1 channel)
Bluetooth 4.0: Vertical MS 4.0
2.4 GHz: 2.4G Wireless Mouse
XP (or higher), MacOS (basic functionality only)
®
*1887257_v1_0319_02_dh_m_en(1)
Record".
to