CE.2
CE.2
I
29
PP
Pulsante APRE / CHIUDE
Ingresso comando.
Il modo di funzionamento di questo ingresso dipende
NO
30
COMMON
dai dip-switch n. 4, n. 5 e n. 6.
31
PED
Pulsante A/C PEDONALE
NO
In modo battente comanda solo l'anta con M1 in modo
scorrevole apre per un tempo regolabile con il trimmer
30
COMMON
PEDEST..
35
ANTENNA
Ingresso per antenna ricevente.
Vedere istruzioni ricevitore per caratteristiche e
34
installazione.
32
SECONDO CANALE
Disponibile solo con riceventi bicanali.
Vedere istruzioni ricevitore per caratteristiche e
33
funzionamento del contatto.
REGOLAZIONI
DIP-SWITCH
La centralina controlla la posizione dei dip-switch solo ad
ogni inizio apertura consigliamo quindi, durante il
collaudo, di attendere sempre la chiusura completa o di
fig.2
resettare la scheda comando cortocircuitando i terminali
come illustrato in fig.2.
RESET
n.1 e n. 2
1 ON / 2 OFF SCORREVOLE
1 ON / 2 ON BASCULANTE
1 OFF / 2 ON ANTA UNICA
1 OFF / 2 OFF BATTENTE
n.3
OFF MEMORIA DEI TEMPI.
ON NO MEMORIA.
n.4
OFF APRE - CHIUDE.
ON APRE - STOP - CHIUDE.
n.5
fig.3
OFF NORMALE.
ON Annullamento dei comandi PP e PED in apertura.
n.6
O N
O N
OFF NORMALE.
ON Annullamento dei comandi PP e PED in pausa.
n.7
O F F
O F F
OFF NORMALE.
ON COLPO SGANCIO.
n.8
n.9
OFF NORMALE.
ON RICHIUSURA AUTOMATICA.
n.10
OFF FISSA.
ON LAMPEGGIANTE.
n.11
OFF SI.
ON NO.
n.12
OFF COSTA FISSA.
ON OROLOGIO.
fig.4
LIMITATORE DI POTENZA
Su ogni uscita motore (M1,M2) viene controllato
MOTOR POWER LIMIT
indipendentemente l'assorbimento da 2 trimmer (fig.4).
Quando questo supera la soglia regolata si accende il
M1
M2
led corrispondente e il quadro comando interviene nel
seguente modo:
- in apertura come scorrevole = intervento costa-fissa
- in chiusura come scorrevole = intervento fotocellula
- in apertura e chiusura come basculante o battente =
finecorsa apre o finecorsa chiude.
MODO
MEMORIA DEI TEMPI
APRE - CHIUDE / APRE - STOP . CHIUDE
APRE/CHIUDE (PP) IN APERTURA
APRE/CHIUDE (PP) IN PAUSA
COLPO SGANCIO
N.C.
RICHIUSURA AUTOMATICA
SPIA LAMPEGGIANTE / SPIA FISSA
LAMPEGGIANTE IN PAUSA
COSTA FISSA / OROLOGIO
UK
OPEN/CLOSE Push button
Command input.
The functioning mode of this input depends on dip
switches 4, 5 and 6.
A/C PEDESTRIAN GATE Push
button
In the wing gate mode, it will only command the wing
with M1 in the slide opening mode for a time that can be
AERIAL
Input for receiver aerial.
See receiver instructions for characteristics and
installation.
SECOND CHANNEL
Only available with a two-channel receiver.
See receiver instructions for characteristics and contact
functioning.
ADJUSTMENTS
DIP SWITCH
Controll panel check the dip switch setting only at the
start moment,we suggest to wait a complete cycle before
change the dip switch. It's possible also reset the logic
card, shortcut terminal as show in fig.2.
Dip 1 and 2 MODE
1 ON / 2 OFF SLIDING GATE
1 ON / 2 ON GARAGE DOOR
1 OFF / 2 ON SINGLE WING GATE
1 OFF / 2 OFF WING GATE
n.3
TIMES MEMORY
OFF TIMES MEMORY.
ON NO MEMORY.
n.4
OPEN-CLOSE / OPEN-STOP. CLOSE
OFF OPEN-CLOSE.
ON OPEN-STOP-CLOSE.
n.5
OPEN/CLOSE (PP) IN THE OPENING PHASE
OFF NORMAL.
ON Cancels PP and PED commands in the opening
phase.
n.6
OPEN/CLOSE (PP) IN PAUSE
OFF NORMAL.
ON Cancels PP and PED commands in pause.
n.7
RELEASE CLICK
OFF NORMAL.
ON RELEASE CLICK.
n.8
N.C.
n.9
AUTOMATIC RECLOSING
OFF NORMAL.
ON AUTOMATIC RECLOSING after a pause time.
n.10
BLINKING/STEADY LIGHT INDICATOR
OFF STEADY LIGHT.
ON BLINKING LIGHT.
n.11
FLASH IN PAUSE
OFF YES.
ON NO.
n.12
FIXED EDGE/TIMER
OFF FIXED EDGE.
ON TIMER.
POWER LIMITER
The device check the current absorption for each output
motor drive. The max. has setting with 2 trimmer as show
in fig.4.
When the read value exceed the preset a led light and
logic card work as follow:
-open with sliding gate = like pneumatic edge fixed.
-close with sliding gate = like photoelectric cell.
- open or close with garage door or wing gate = limit
switch open or limit switch close.
F
Bouton OUVRE / FERME
Entrée commande.
Le mode de fonctionnement de cette entrée dépend des
dip-switch n°4, n°5 et n°6.
Bouton O/F PIÉTONS
En mode "à battant", il commande uniquement le
battant avec M1, en mode "coulissant", il commande
l'ouverture pendant un temps réglable avec le trimmer
PEDEST.
ANTENNE
Entrée pour antenne du récepteur.
Voir notice récepteur pour caractéristiques et
installation.
DEUXIÉME CANAL
Disponible seulement avec récepteurs à deux canaux.
Voir notice récepteur pour caractéristiques et
fonctionnement du contact.
RÉGLAGES
DIP-SWITCH
La centrale contrô le la position des dip-switchs
seulement à chaque début d'ouverture. Nous
conseillons donc pour l'essai d'attendre toujours la
fermeture complète ou de ré initialiser la carte de
commande en shuntant les bornes comme l'illustre la
fig. 2
n.1 et n. 2
MODE
1 ON / 2 OFF PORTE OU PORTAIL COULISSANT
1 ON / 2 ON PORTE BASCULANTE
1 OFF / 2 ON PORTE OU BATTANT UNIQUE
1 OFF / 2 OFF PORTE OU PORTAIL À BATTANTS
n.3
MÉMOIRE DES TEMPS
OFF
MÉMOIRE DES TEMPS
.
ON
PAS DE MÉMOIRE.
n.4
OUVRE - FERME / OUVRE - STOP - FERME
OFF OUVRE - FERME.
ON OUVRE - STOP - FERME.
n.5
OUVRE/FERME (PP) EN OUVERTURE
OFF NORMAL.
ON
Annulation des commandes PP et PED en
ouverture.
n.6
OUVRE/FERME (PP) EN PAUSE
OFF NORMAL.
ON
Annulation des commandes PP et PED en pause
n.7
IMPULSION DÉCLENCHEMENT
OFF NORMAL.
ON
COUP DÉCLENCHEMENT.
n.8 N.C.
n.9
REFERMETURE AUTOMATIQUE
OFF NORMAL
ON
REFERMETURE AUTOMATIQUE
.
n.10
VOYANT CLIGNOTANT / VOY ANT FIXE
OFF FIXE.
ON CLIGNOTANT.
n.11
CLIGNOTANT EN PAUSE
OFF OUI.
ON NO.
n.12
BARRE PALPEUSE FIXE / TEMPORISATEUR
OFF
BARRE PALPEUSE FIXE.
ON
TEMPORISATEUR.
LIMITEUR DE PUISSANCE
Sur chaque sortie moteur (M1, M2) l'absorption est
contrôlée indépendamment par 2 trimmers (fig. 4).
Quand l'absorption dépasse le seuil préfixé, la DEL
correspondante s'allume et le tableau de commande
intervient de la manière suivante:
-en ouverture comme porte/portail coulissant =
intervention barre palpeuse fixe
-en fermeture comme porte/portail coulissant =
intervention cellule photoélectrique
-en ouverture et en fermeture comme porte basculante
ou portail à battants = microint. de fin de course
d'ouverture ou microint. de fin de course de fermeture
pag. 3