Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-8533, H-8534
MOBILE GLASS
DRY ERASE BOARD
TOOLS NEEDED
3.5 mm Hex
Caster Wrench
Wrench (included)
(included)
Glass Board x 2
Leg x 2
Plastic
Top Cap x 1
End Cap x 6
Figure 1
Plastic
End Cap
A
Plastic
End Cap
PAGE 1 OF 9
1-800-295-5510
uline.com
14 mm Wrench
PARTS
Horizontal Tube x 2
1/4 x 15 mm
1/4 x 50 mm
Screw x 6
Screw x 8
ASSEMBLY
Lock Washer
Locking
Caster
Lock Washer
Non-Locking
Caster
Three-Person Assembly
Required
Vertical Tube x 2
Leg Connector x 1
Lock Washer x 4
1.
Place a lock washer on each caster's stem and
screw one locking and one non-locking caster onto
each leg. Fully tighten the nuts that accompany
each caster. (See Figure 1)
2. Insert one plastic end cap into top end of each leg.
(See Figure 1A)
NOTE: Make sure the curve of the legs are
oriented facing inward.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Marker Tray x 1
Locking
Non-Locking
Caster x 2
Caster x 2
0621 IH-8533
Publicité
Sommaire des Matières pour Uline H-8533
- Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-8533, H-8534 1-800-295-5510 uline.com MOBILE GLASS DRY ERASE BOARD TOOLS NEEDED Three-Person Assembly 3.5 mm Hex Caster Wrench 14 mm Wrench Required Wrench (included) (included) PARTS Glass Board x 2...
- Page 2 ASSEMBLY CONTINUED 3. Connect legs with leg connector. Use two 1/4 x 50 mm Figure 2 1/4 x 50 mm screws on each leg. Tighten completely. Screws (See Figure 2) 1/4 x 50 mm Screws Connector 4. Insert the vertical tubes into the horizontal tubes. Figure 3 (See Figure 3) Vertical...
- Page 3 Place a glass board into marker tray's inner flanges Figure 6 on each side of the board. (See Figure 6) Top Cap NOTE: Glass boards on the H-8533 (3 x 4') are 1/4 x 15 mm vertical. Glass boards on the H-8534 (6 x 4') Screws are horizontal.
- Page 4 H-8533, H-8534 800-295-5510 uline.mx HERRAMIENTAS NECESARIAS Se Requiere Armar Entre Llave Hexagonal Llave Española Llave de 14 mm Tres Personas de 3.5 mm (incluida) (incluida) PARTES 2 Pizarrones 2 Patas 2 Tubos 2 Tubos 1 Conector 1 Bandeja para de Vidrio...
- Page 5 CONTINUACIÓN DEL ENSAMBLE 3. Conecte las patas con el conector de patas. Use Tornillos de dos tornillos de 1/4 x 50 mm en cada pata. Apriete Diagrama 2 1/4 x 50 mm por completo. (Vea Diagrama 2) Tornillos de 1/4 x 50 mm Conector de Pata 4.
- Page 6 Tapa Superior lado del pizarrón. (Vea Diagrama 6) Tornillos de NOTA: Los pizarrones de vidrio en el H-8533 (3 x 4') 1/4 x 15 mm son verticales. Los pizarrones de vidrio en el H-8534 (6 x 4') son horizontales.
- Page 7 H-8533, H-8534 1-800-295-5510 uline.ca OUTILS REQUIS Montage à trois Clé hexagonale Clé pour Clé de 14 mm personnes requis de 3,5 mm (inclus) roulette (inclus) PIÈCES Tableau en Pied x 2 Tube horizontal x 2 Tube vertical x 2 Raccord de...
- Page 8 MONTAGE SUITE 3. Reliez les pieds au raccord de pied. Utilisez Vis de Figure 2 deux vis de 1/4 x 50 mm sur chaque pied. Serrez 1/4 x 50 mm complètement. (Voir Figure 2) Vis de 1/4 x 50 mm Raccord de pied 4.
- Page 9 (Voir Figure 6) Vis de REMARQUE : Les tableaux en verre du H-8533 (3 x 4 pi) 1/4 x 15 mm sont verticaux. Les tableaux en verre du H-8534 (6 x 4 pi) sont horizontaux.