Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

CEFB36H-BS
MULTIPLE PRODUCT CODES (LEAVE BLANK IF N/A)
SAFETY INFORMATION
WARNING
!
FIRE OR EXPLOSION HAZARD
If the information in these instructions are
not followed exactly, a fi re or explosion may
result causing property damage, personal
injury, or loss of life.
- Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity of
this or any other appliance.
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.continentalfi replaces.com • hearth@continentalfi replaces.com
$10.00
INSTALLATION AND
ADD MANUAL TITLE
OPERATION MANUAL
WARNING!
WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN
- SWALLOWING MAY LEAD TO SERIOUS INJURY IN AS LITTLE AS 2 HOURS
OR DEATH, DUE TO CHEMICAL BURNS AND POTENTIAL PERFORATION OF
THE OESOPHAGUS.
- IF YOU SUSPECT YOUR CHILD HAS SWALLOWED OR INSERTED A
BUTTON BATTERY, IMMEDIATELY SEEK URGENT MEDICAL ASSISTANCE.
- EXAMINE DEVICES AND MAKE SURE THE BATTERY COMPARTMENT IS
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CORRECTLY SECURED, E.G. THAT THE SCREW OR OTHER MECHANICAL
FASTENER IS TIGHTENED. DO NOT USE IF COMPARTMENT IS NOT
SECURE.
- DISPOSE OF USED BUTTON BATTERIES IMMEDIATELY AND SAFELY. FLAT
BATTERIES CAN STILL BE DANGEROUS.
- TELL OTHERS ABOUT THE RISK ASSOCIATED WITH BUTTON BATTERIES
AND HOW TO KEEP THEIR CHILDREN SAFE.
CSA /
INTERTEK
LOGO
Electric Built-In Appliance
Product Name / Code
(MUST use title from Price Book)
ADD PRODUCT CODE
(IF MULTIPLE, _____ ILLUSTRATED)
ADD PRODUCT IMAGE
ADD BUTTON BATTERY WARNING IF APPLICABLE
This appliance has a remote that requires button
batteries that are hazardous to young children.
IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD "PLACE
BARCODE LABEL ON THE OWNER'S MANUAL"
ENGLISH
FRENCH PG. 27
(CEFB36H-BS Illustrated)
ENFANTS
- L'INGESTION P
HEURES OU LA
RATION POTEN
FOR INDOOR USE ONLY
- SI VOUS PENS
BOUTON, CONS
- EXAMINEZ LES
CSA C22.2 NO. 46 / UL 2021
CSA 2.22 NO. 46 / UL 1278
BATTERIE EST B
EST SERRÉE. N
- ÉLIMINER LES
SÉCURITÉ. LES
- RENSEIGNEZ-
FAÇON DE GAR
W415-2947 / A / 09.01.20
AVERT

Publicité

Chapitres

Table des Matières
loading

Sommaire des Matières pour Continental CEFB36H-BS

  • Page 1 FRENCH PG. 27 INSTALLATION AND ADD MANUAL TITLE OPERATION MANUAL Electric Built-In Appliance Product Name / Code (MUST use title from Price Book) (CEFB36H-BS Illustrated) ADD PRODUCT CODE (IF MULTIPLE, _____ ILLUSTRATED) ADD PRODUCT IMAGE SAFETY INFORMATION WARNING WARNING! FIRE OR EXPLOSION HAZARD...
  • Page 2 safety information WARNING • If equipped with a heater, this appliance can be hot when operated and can cause severe burns if contacted. • Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fi re or injury. •...
  • Page 3 • It is normal for your electric appliance to produce noise, especially when installed in a quiet space such as a bedroom. safety information WARNING • To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a carpet, where openings may become blocked.
  • Page 4: Table Des Matières

    table of contents general information dimensions hardware list listing approvals general instructions unpacking and testing appliance rating plate information label location locating appliance grounding appliance installation and finishing minimum clearance to combustibles minimum mantel clearances rough framing appliance installation and finishing electrical information 120V cord plug installation wiring diagram...
  • Page 5: General Information

    dimensions 1.0 general information dimensions FRONT VIEW SIDE VIEW 30 3/4” 25 7/8” (781mm) (657mm) 31 7/8” (810mm) 33 7/8” 10 5/8” (860mm) (270mm) 36 1/8” 11 1/4” (918mm) (286mm) TOP VIEW 34 5/8” (879mm) 28 7/8” (733mm) hardware list Ref.
  • Page 6: Listing Approvals

    This appliance has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer. Model No. CEFB36H-BS note: Description 36" Electric Appliance...
  • Page 7: Rating Plate Information

    CATION: BLACK LETTERING ON SILVER BACKGROUND. MINIMUM FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm) RALL SIZE: 6" x 3" UMBERS TO BE ASCENDING FROM CEFB36H200901. Ref. Part Number Label Description DWG#: W385-2556 RATING PLATE (CEFB36H-BS) W385-2210 "Do Not Cover" 09.01.20_X.L. DATE: Model & Serial Number W385-2370...
  • Page 8: Locating Appliance

    2.0 locating appliance WARNING • Due to high temperatures, this electric appliance should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 36” (91.4cm) from the front of the appliance. •...
  • Page 9: Installation And Finishing

    • Do not run the power cord horizontally, directly below the appliance. Your CEFB36H-BS is a recessed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas. 42.5 note: Follow all national and local electrical codes.
  • Page 10: Rough Framing

    installation and finishing rough framing WARNING • Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from combustible materials such as curtains, drapes, furniture, bedding, paper, etc. note: It is recommended to complete finishing of the wall before fully securing the appliance. Once the rough framing and the finishing materials have been prepared and the power has been routed to the right side of the recess, the appliance may be installed.
  • Page 11: Appliance Installation And Finishing

    installation and finishing appliance installation and finishing 1. Remove the front decorative cover held in place by 2 magnets (Fig. 3-1). 2. With one hand on the glass door to prevent it from falling, remove the 2 screws holding the glass door in place (Fig.
  • Page 12 installation and finishing 5. Complete hard-wiring (see "electrical information" section). note: It is recommended to complete finishing of the wall before fully securing the appliance (Fig. 3-6). 6. Carefully lift the appliance into the rough-in framing (Fig. 3-7). Fig. 3-6 Fig.
  • Page 13 installation and finishing 8. Remove the 4 screws holding the back retainers in place (Fig. 3-9). Set the screws and retainers aside (Fig. 3-10). Repeat on opposite side. Fig. 3-9 Fig. 3-10 9. Place the brick panels into the bottom retainers and behind the side retainers (Fig. 3-11). Side retainer Repeat on...
  • Page 14 installation and finishing 11. Re-install the log set without reinstalling the 4 screws removed in step 4 (Fig. 3-14). 12. Re-install the glass door (Fig. 3-15 and 3-16). 13. Re-install the front decorative cover held in place by 2 magnets (Fig. 3-17). Framing hidden for clarity.
  • Page 15: Electrical Information

    4.0 electrical information 120V cord plug installation The factory default setting is 120 volt cord plug installation configuration. Simply plug the appliance to a grounded 120V, 15 amp outlet box. note: This appliance must be connected to a dedicated 15 amp circuit. The use of an extension cord is NOT permitted.
  • Page 16: Hard-Wiring Installation

    electrical information hard-wiring installation WARNING • Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance. HARD-WIRING CONNECTION If it is necessary to hard-wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring.
  • Page 17: Operating Instructions

    5.0 operating instructions WARNING • Ensure the house circuit breakers for the circuit supply are turned on. When initially connecting the appliance to a power source, the appliance will make a beeping sound to indicate standby mode. Once the appliance has been plugged into a grounded electrical outlet or hard-wired to a dedicated 120V or 240V power supply, it is ready to operate.
  • Page 18: Operating Remote Control

    operating instructions operating remote control Turns the appliance on / off. Power Turns the timer on /off. Timer 10 Settings: -- (no setting), 30 min., 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h Controls the appliance temperature. 11 Settings: °C Temperature °F Control...
  • Page 19: Remote Battery Installation

    operating instructions remote battery installation WARNING • This remote control requires button batteries that are hazardous to young children. • WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. WARNING! • Swallowing may lead to serious injury or death in as little as 2 hours due to chemical burns and potential perforation of the oesophagus.
  • Page 20: Replacement Parts

    7.0 replacement parts WARNING • Failure to position the parts in accordance with this manual or failure to use only parts specifi cally approved with this appliance may result in property damage or personal injury. Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can be ordered through your Authorized dealer / distributor.
  • Page 21 replacement parts W415-2947 / A / 09.01.20...
  • Page 22: Troubleshooting

    8.0 troubleshooting WARNING • Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance. symptom problem solution Appliance will not Appliance is not plugged into an Check plug, and plug in the appliance if necessary. come on when electrical outlet.
  • Page 23 troubleshooting symptom problem solution Ember bed is Brightness not selected. See “operation” section. No difference from Hard wire connections are not See “hard-wiring installation” section. not glowing or H1 to H2. correct. Ember LED issue. Inspect the ember bed LEDs and replace, if necessary. dimming.
  • Page 24: Warranty

    Additional service fees may apply if you are seeking warranty service from a dealer. All specifi cations and designs are subject to change without prior notice due to on-going product improvements. CONTINENTAL® is a registered trademark of Wolf Steel Ltd.
  • Page 25: Notes

    10.0 notes 29.1 W415-2947 / A / 09.01.20...
  • Page 26 7200, Route Transcanadienne, Montréal, Québec H4T 1A3 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8 103 Miller Drive, Crittenden, Kentucky, USA 41030 De Riemsdijk 22, 4004 LC Tiel, The Netherlands Phone: 1-866-820-8686 continentalfireplaces.com...
  • Page 27 FRANÇAIS MANUEL D'INSTALLATION ADD MANUAL TITLE ET D'OPÉRATION Appareil Électrique Encastré Product Name / Code (MUST use title from Price Book) (CEFB36H-BS Illustré) ADD PRODUCT CODE (IF MULTIPLE, _____ ILLUSTRATED) ADD PRODUCT IMAGE CONSIGNES DE SÉCURITÉ AVERTISSEMENT WARNING! RISQUE D’INCENDIE OU D’EXPLOSION WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN Si ces instructions ne sont pas suivies à...
  • Page 28 consignes de sécurité AVERTISSEMENT • Si équipé avec un chauffage, cet appareil peut être chaud lorsqu’il fonctionne et peut causer de graves brûlures en cas de contact. • Ne faites pas fonctionner l’appareil avant d’avoir lu et compris les instructions d’utilisation. L’incapacité de respecter les instructions pourrait causer un incendie ou des blessures corporelles.
  • Page 29 consignes de sécurité AVERTISSEMENT • Pour prévenir les risques d’incendie, ne bloquez pas les entrées d’air et les sorties d’air de quelque manière que ce soit. Ne placez pas cet appareil sur une surface molle telle qu’un tapis où les ouvertures pourraient se bloquer.
  • Page 30 table de matières information générale dimensions liste de pièces homologations instructions générales déballage et verification d'appareil information à propos de plaque d'homologation emplacement d'étiquettes emplacement d'appareil mise à terre d'appareil installation et finitions dégagements minimaux aux combustibles dégagements minimaux à la tablette ossature approximatif installation d'appareil et finitions information électrique...
  • Page 31: Information Générale

    dimensions 1.0 information générale dimensions VUE DE FACE VUE DE CÔTÉ 30 3/4” 25 7/8” (781mm) (657mm) 31 7/8” (810mm) 33 7/8” 10 5/8” (860mm) (270mm) 36 1/8” 11 1/4” (918mm) (286mm) VUE DE DESSUS 34 5/8” (879mm) 28 7/8” (733mm) liste de pièces Réf.
  • Page 32: Homologations

    Cet appareil a été testé selon les normes CSA pour les appareils électriques installés de façon permanentes aux États-Unis et au Canada. Si vous avez besoin d'assistance durant l'installation, veuillez contacter votre détaillant local. N° de Modèle CEFB36H-BS note: Description Appareil Électrique de 36"...
  • Page 33: Information À Propos De Plaque D'homologation

    RALL SIZE: 6" x 3" Réf. N° de Pièce Description UMBERS TO BE ASCENDING FROM CEFB36H200901. W385-2210 « Ne Pas Couvrir » DWG#: W385-2556 RATING PLATE (CEFB36H-BS) Modèle & N° de Sérial 09.01.20_X.L. DATE: W385-2370 Schéma de Câblage W385-2368 Plaque d'Homologation W385-2167 «...
  • Page 34: Emplacement D'appareil

    2.0 emplacement d'appareil AVERTISSEMENT • En raison des températures élevées, cet appareil électrique doit être situé hors de circulation. Conservez des matériaux combustibles tels que des meubles, des coussins, les litières, des papiers, des vêtements, et des rideaux au moins 36" (91,4cm) de l'avant de l'appareil. •...
  • Page 35: Installation Et Finitions

    • N’exécutez pas le cordon d’alimentation horizontalement, directement en dessous de l’appareil. Votre CEFB36H-BS est un appareil encastré. Sélectionnez un endroit approprié qui ne soit pas susceptible d'être 42.5 humide et qu'il soit éloigné des rideaux, des meubles, et des zones à fort trafic.
  • Page 36: Ossature Approximatif

    installation et finitions ossature approximatif AVERTISSEMENT • Choisissez un endroit non sujet à l'humidité et situé au moins de 36" (91,4cm) des articles combustibles, tels que les rideaux, meubles, literie, papier, etc. note: Il est recommandé de compléter la finition du mur avant de fixer complètement l'appareil. Une fois que l'ossature approximatif et les matériaux de finitions ont été...
  • Page 37: Installation D'appareil Et Finitions

    installation et finitions installation d'appareil et finitions 1. Retirez le couvercle décoratif en avant qui est tient en place avec 2 aimants (Fig. 3-1). 2. Avec une main sur le verre pour le-prevenir de tomber, retirez les 2 vis servant à fixer la porte vitrée en place (Fig.
  • Page 38 installation et finitions 5. Complètez le branchement par câble (voir la section « information électrique »). note: Il est recommandé de compléter la finition du mur avant de fixer complètement l'appareil (Fig. 3-6). 6. Soigneusement soulevez l'appareil dans l'ossature approximatif (Fig. 3-7). Fig.
  • Page 39 installation et finitions 8. Retirez les 4 vis servant à fixer les supports de retenue en place (Fig. 3-9). Mettez au côté les vis et les suports (Fig. 3-10). Répétez au côté opposé. Fig. 3-9 Fig. 3-10 9. Placez les panneaux en brique dans les supports inférieurs et à l'arrière les supports de côté (Fig. 3-11). Support de Côté...
  • Page 40 installation et finitions 11. Réinstallez l'ensemble de bûche sans réinstaller les 4 vis précédemment retirées en étape 4 (Fig. 3-14). 12. Réinstallez la porte vitrée (Fig. 3-15 et 3-16). 13. Réinstallez le couvercle décoratif en avant qui est tient en place avec 2 aimants (Fig. 3-17). L'ossature masquée par souci...
  • Page 41: Information Électrique

    4.0 information électrique installation de prise de courant 120V Le réglage de défaut en usine est une configuration d'installation d'une prise de courant 120V. Branchez l'appareil d'une boîte de sortie de 120V, 15 ampères mise à la terre. note: Cet appareil doit être connecté à un circuit de 15 ampères dédié. L'utilisation d'un cordon d'extension N'EST PAS autorisée.
  • Page 42: Installation De Branchement Par Câble

    information électrique installation de branchement par câble AVERTISSEMENT • Coupez l'alimentation électrique à l'appareil et laissez-le refroidir avant d'effectuer un entretien. Seul un technicien de service qualifié peut effectuer l'entretien ou la réparation de cet appareil électrique. BRANCHMENT PAR CÂBLE Si c'est nécessaire de faire un branchement par câble, un électricien qualifié...
  • Page 43: Installation De Branchement Par Câble 240V

    information électrique 4.3.2 installation de branchement par câble 240V 1. Retirez les 4 vis servant à fixer le cordon et la plaque de recouvrement au côté de la chambre de combustion. 2. Dévissez les connecteurs de fils servant à fixer le cordon d'alimentation et le fil L2. 3.
  • Page 44: Instructions De Fonctionnement

    5.0 instructions de fonctionnement AVERTISSEMENT • Assurez-vous que les disjoncteurs de la maison pour ce circuit soien allumés. Lorsque vous connectez l'appareil d'une source d'alimentation pour la première fois, l'appareil va faire un bip d'indiquer le mode veille. Une fois que l'appareil est branché dans une prise de courant mise à la terre ou câblé...
  • Page 45: Fonctionnement De Télécommande

    instructions de fonctionnement fonctionnement de télécommande Allume / éteint l'appareil. Alimentation Allume / éteint la minuterie. Minuterie 10 Réglages: -- (pas de réglage), 30 min., 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h Contrôle la température de l'appareil. 11 Réglages: °C Contrôle de °F...
  • Page 46: Installation De Pile De Télécommande

    instructions de fonctionnement installation de pile de télécommande AVERTISSEMENT • Cette télécommande nécessite des piles bouton qui sont dangereuses pour les jeunes enfants. • AVERTISSEMENT! GARDEZ DES PILES DE LA PORTÉE DES ENFANTS. • L'ingestion peut entraîner des blessures graves ou la mort dans moins de 2 heures, en WARNING! AVER raison des brûlures chimiques et de la perforation potentielle de l'oesophage.
  • Page 47: Pièces De Rechange

    7.0 pièces de rechange AVERTISSEMENT • Omettre de positionner les pièces conformément à ce manuel ou d’utiliser uniquement des pièces spécifi quement approuvées pour cet appareil peut causer des dommages matériels ou des blessures corporelles. Contactez votre détaillant pour les questions concernant les prix et la disponibilité des pièces de remplace- ment.
  • Page 48 pièces de rechange W415-2947 / A / 09.01.20...
  • Page 49: Guide De Dépannage

    8.0 guide de dépannage AVERTISSEMENT • Coupez l’alimentation électrique à l’appareil et laissez-le refroidir avant d’effectuer un entretien. Seulement un technicien de service qualifié peut effectuer l’entretien ou la réparation de cet appareil électrique. symptôme problème solution L’appareil L’appareil n’est pas branché Vérifiez la prise, et branchez dans l’appareil si nécessaire.
  • Page 50 guide de dépannage symptôme problème solution La luminosité du Pas de différence Éclat de flamme n’est pas Branchement par câble sont Voir la section « fonctionnement ». Voir la section « branchement par câble ». jeu de flammes sélectionné. de H1 à H2. incorrectes.
  • Page 51: Garantie

    Nonobstant toutes les dispositions contenues dans cette garantie limitée, la responsabilité de CONTINENTAL® sous cette garantie est défi nie comme ci-dessus et elle ne s’étendra à aucun dommage accidentel, consécutif ou indirect.
  • Page 52 7200, Route Transcanadienne, Montréal, Québec H4T 1A3 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8 103 Miller Drive, Crittenden, Kentucky, USA 41030 De Riemsdijk 22, 4004 LC Tiel, The Netherlands Phone: 1-866-820-8686 continentalfireplaces.com...

Table des Matières