Finder 7E.56 Instructions De Montage Et D'exploitation page 6

Assembly and operating instructions Type 7E.56
5 A-active-energy meter, three-phase for current transformer, Fig. 1
Description
The 7E.56 is a compact electronic active power energy
meter for application in 3-phase power lines for current
transformer and neutral conductor. Depending on the
type, the well readable LCD display offers the reading
of additional values like instantaneous power, total or
per phase, as well as voltages and currents per phase.
Technical data
Connection Fig. 2
■
diagram
Dimensions Fig. 3
■
Accuracy class B, according to EN 50 470-3,
■
Cl. 1 according to IEC 62 053-21
Reference, Maxi- I = 5 A, Ima
ref
■
mum, initial current
operating voltage 3 × 230/400 V
■
Tolerance -20%/+15%
Counting range 000000,0...9999999 kWh
■
S0 output Optocoupler 5 - 30 V
■
(Interface) Impedance 100 Ω,
pulse duration 30 ms
10 Imp./kWh.
Transmission- Maximum 1000 m (at 30 V/20 mA)
■
distance
Connections Conductor cross-section 1,5 - 16 mm
■
Main circuit Screwdriver Pozi No. 1, slotted
No. 2, breakaway torque 1,5 - 2 Nm
Connections Conductor cross-section max. 2,5 mm
■
Control circuit Screwdriver Pozi No. 0, slotted
No. 2, breakaway torque 0,8 Nm
Operating -10 ... +55°C (noncondensing
■
temperature according standard EN 50 470)
Indicating elements
(Fig. 4)
T1total (kWh) Shows total consumption
■
T1part. (kWh) Shows partial consumption for,
■
this value is resettable
CT Shows the set
■
current transformer ratio
Select The transformer ratio can be selected
■
in Menu item Select, in the open
bridge Z1-Z2
P(kW) Shows the instantaneous power
■
per phase or all phases
U(V) Shows the voltage per phase
■
I(A) Shows the current per phase
■
n Imp/kWh Pulsates according to drawn
■
power
kWh Shows the unit kWh when the
■
consumption is displayed
L1 / L2 / L3 For P-, U-, I- or Error display, the
■
corresponding phase is displayed
Error In case of missing phase or wrong
■
current direction. The corresponding
phase is additionally displayed.
4 319 5086 0a
6 A, Ist = 10 mA
x =
, 50 Hz
AC
/20 mA,
DC
FINDER SpA
02.2010
Via Drubiaglio, 14
10040 Almese (TO) - ITALY
Notes before connecting
1. Do not connect L1, L2 to L3 to N.
2. In order to avoid moisture in the meter due to
condensate build-up, acclimatise the meter at room
temperature for about half an hour before connecting.
Attention!
These devices must only be installed by a professional
electrician, otherwise there is the risk of fire or the risk
of an electric shock.
Operation of the LCD display
The operating menu is shown as a graph on the
figure 4. For setting the transducer value, the bridge
Z1-Z2 must be removed. After setting, this connection
must be restored.
Installation instructions
The three phase energy meter can be attached to a
35 mm rail (EN 60715TH35).
The meter can be used only in installation cabinets.
Declaration of Conformity CE
,
2
Finder SpA declares at its own responsibility:
The following energy meters are in compliance:
,
2
7E.56.8.400.0000
■
7E.56.8.400.0010
■
The following energy meters are approved for energy
billing:
7E.56.8.400.0010
■
which this certificate refer to, are in accordance with
the following standards:
EN 50470 parts 1 and 3 (electronic meter), of
■
October 2006.
Directive 2004/22/EG of the European
■
parliament and of the council regarding measuring
instruments
• Annex I, essential requirements
• Annex MI-003, active electrical energy meters
EC - Declaration of Conformity: 2009
Finder SPA
Conformity Assessment Body:
Zertifizierungstelle METAS-Cert, Nr. 1259
CH-3003 Bern-Wabern
Signed: Marcello Grande, Technical Manager
English
Subject to change without notice