Publicité
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
»
Care &
Safety Advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check against the
contents
list.
For
safety purposes we
strongly recommend the product to
be
assembled by
at least
two
people.
Some parts have
metal
edges. Please be careful when
handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to
assemble the Gazebo
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the Gazebo
if
you
are
tired,
have
taken drugs,
medications
or alcohol, or if you are prone to dizzy spells.
When using
a
stepladder
or
power tools,
make sure
that
you are
following the
manufacturer's safety advice.
Do
not climb
or stand
on
the
roof.
Heavy articles should
not
be
leaned against the poles.
Keep
roof and gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on
roof
can
damage the Gazebo making
it unsafe
to
stand
below
or nearby.
This
product
was
designed to
be used
mainly
as
a
Gazebo.
If color
was scratched
during assembly it
can be
fixed
with the following tint:
Grey
-
RAL
7012
»
Cleaning Instructions
In
order to
clean
the
Gazebo,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
»Tools
&
Equipment
TO01(Supplied)
6,
Attention
Please
note you install the panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT") and peel
the film strip covering the
panels.
Screws and plugs are
not supplied.
Please
tighten
all screws
when completing
assembly.
Anchoring this product to the ground
is
essential
to
its
stability
and
rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
When
encountering the information
icon, please refer
to the
relevant assembly step for additional comments and
assistance.
»
During Assembly
During assembly
use
a
soft surface below the parts to avoid scratches and damages.
Step 8: Optional
-
if
you wish
to
add curtains
/
mosquito netting
-
Please
thread the plastic clips
through
the
rail
in
each
profile.
(Curtains
/
mosquito netting
are
not supplied).
Add clips according to the specific
quantity of curtain
rings.
Step
10:
It
is
recommended to
use
a
carton or other soft material under the lowered
corner
in
order to avoid
scratches and
peeling
of
paint.
Steps 10a+12a:
Please
note that
screws
insertion should
be
done from the outside.
Steps 11+13:
Please
note
that
screws
insertion should
be
done from the
bottom
up.
Afterwards
please use
the tool T001.
Step
14:
Please
add silicone
on
the inner
area
of
part #8030
as
illustrated.
Step 20:
Please
drill
holes
in
the
panels, parallel
to the
holes
in
profiles
#7663.
Step 21:
Please level
the profiles'
legs
and adapt
screws and plugs
to your specific
ground type.
Publicité
