EOS
360
®
HEADLAMP &
SAFETY FLASHER
Operating and Maintenance
Instructions
Notice d'utilisation et d'entretien
und Wartungsanleitung
princetontec.com
ENGLISH
Battery Installation
- See Figure 1
3 AAA
• Alkaline (LR03)
• Lithium (L92)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment
and recommends recycling batteries. For more
information about battery recycling, please go to
www.batteryrecycling.com.
Requires coin or small flat tipped screw driver.
Install three AAA batteries according to the polarity
markings on the inside of the cabinet. Observe
proper battery polarity when installing the batteries.
Improper installation of the batteries will damage
the light and void the warranty.
Rotate the door to the closed position, squeeze the
body between your forefingers and thumb to snap
the door latch over
the catch.
WARNING !
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry
types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Lithium batteries offer extended
constant brightness time, extreme cold weather
performance, and are lighter weight. Rechargeable
NiCad or NiMH batteries may result in reduced
brightness due to lower nominal voltage.
The EOS 360 battery compartment has a
waterproof seal. It is important to keep this seal free
from dirt and away from harsh chemicals in order to
preserve waterproof integrity. Inspect the seal every
time batteries are changed. If dirt is present, wipe
gently with a damp cotton swab and mild soap until
dirt is removed.
NOTE: Some battery types can emit hydrogen
gas, which can create an explosion potential in
sealed devices if it is not vented or removed. The
EOS 360 is equipped with a platinum catalyst to
remove this gas. Upon severe impact, the catalyst
could fracture. If you notice a rattling sound in
the headlamp or gray particles in the battery
compartment, do not use the headlamp. See the
warranty and return policy for more information.
Switch Operation
– See Fig 2
Modes (High, low and flash) are selected by
pressing and releasing the button within 1.5
seconds of the previous button press.
There are two ways to turn the EOS 360 off. You
can cycle through the modes until you reach off or
if more than two seconds have passed since the
previous button press, holding the button for 1.5
seconds will turn the light off.
Figure 1 – Battery Replacement
1
0119
Figure 2 – Switch Operation
*Visibility Rating: Flat and unobstructed viewing is visible up to 1050 feet and is rated to-be-seen
Figure 3 - Performance
Mode
HEADLAMP ONLY
High
Low
Strobe
HEADLAMP W/ BAND & CONSTANT
High
Low
BAND ONLY
Band Constant
Band Strobe
HEADLAMP W/ BAND & STROBE
High
Low
• Princeton Tec calculates total burn time as the time it takes for the light source to produce a minimum of 0.25 lux at 2
meters. 0.25 lux is about the equivalent of a full moon on a clear night.
Troubleshooting
If the EOS 360 fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check the light for water contamination. The light
will resume normal operation once the water is
shaken or blown out and the light is left open until
completely dry. If the light has been contaminated
with salt water, flush the unit with fresh water and
dry as described above
USA– International 1-Year Warranty
WARRANTY – Princeton Tec warrants this product to
be free from defects in workmanship and materials
under normal use for one year from the original
date of purchase. This warranty covers all of the
component parts of the product except batteries.
This warranty does not cover deterioration due to
normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair.
Princeton Tec will repair or replace parts which
are defective in workmanship or materials. Your
authorized Princeton Tec Dealer and Princeton Tec
are the only facilities authorized to repair the product.
After (3) unsuccessful attempts (within the warranty
period) to repair the product, you have the right to
elect replacement of the product or a refund of the
purchase price less allowance for use of the product.
NO INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARE INCLUDED IN THIS WARRANTY. (Some states
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
2
3
press 1x = High
press 1x = High
press 2x = Low
press 2x = Low
press 3x = Flash
press 3x = Flash
press 4x = Off
press 4x = Off
press 1x = On
press 1x = On
press 2x = Flash
1x
press 2x = Flash
1x
press 3x = Off
press 3x = Off
Burntime
21.5h
50h
51h
4.1h
20 h
27h
100h
4.5h
34h
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA)
a chemical known to the State of California to cause
birth defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement,
first contact Princeton Tec customer service on
1-800-257-9080 to request an RMA number.
Please have your light model, date of purchase
and a brief description of the fault you are
experiencing. No warranty repairs will be accepted
without an RMA number.
3. Return the light without batteries to: Princeton Tec,
PO Box 8057 Trenton NJ 08650. Postage due
and freight collect items will not be accepted.
4. Upon receipt your light will be processed in
about two weeks. Please allow additional time for
return transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2019 Princeton Tec
4
Headlamp
Headlamp
Headband
Headband
2x
3x
2x
3x
Distance
68m
34m
68m
72m
29m
*1050m
*1050m
72m
33m