Technical Data; Dimensions, Weights, Ambient Conditions; Supply Voltage (External); Control Signals - Balluff BTL5-H1-M-P-S 92/KA Serie Mode D'emploi

BTL5-H1_ _-M_ _ _ _-P-S92/KA_ _
Micropulse Linear Transducer in Profile Housing
8

Technical Data

The following are typical values at DC 24 V and 25 °C. Fully operational after power-up, with full accuracy after warm-
up. Values are with BTL5-P-3800-2, BTL5-P-4500-1 or BTL5-P-5500-2 magnet held at a constant offset from the
transducer or with captive magnet BTL5-F/M/N-2814-1S (see magnet section for exceptions):
Resolution:
Position > 5 µm
settable over SDO
in steps of 5 µm
Speed > 0.1 mm/s
settable over SDO
in steps of 0.1 mm/s
Meas. rate f = 1kHz
standard
Non-linearity ± 30 µm
Hysteresis < 1 LSB
Repeatability < 2 LSB
(resolution + hysteresis)
Temperature coefficient
(6 µm + 5 ppm * Length)/K
Shock loading 100 g/6 ms
1
per IEC 60068-2-27
Continuous shock 100 g/2 ms
per IEC 60068-2-29 1
Vibration 12 g, 10 to 2000 Hz
per IEC 60068-2-6 1
1
Individual specifications as per
Balluff factory standard
8.1 Dimensions, weights,
ambient conditions
Nominal length < 4000 mm
➥ ➥ ➥ ➥ ➥ pages 4 and 5
Dimensions
Weight approx. 1.4 kg/m
Housing anodized aluminum
Housing attachment
Mounting clamps with isolation
bushings and screws
Operating temp. –40 °C to +85 °C
Humidity < 90%, non-condensing
Protection class per IEC 60529
IP 67 when closed up
8.2

Supply voltage (external)

Regulated supply voltage
BTL5-H1... DC 20 to 28 V
Ripple 24 V ± 2 V
Current draw < 100 mA
Inrush < 3 A/0.5 ms
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing 500 V
8
english
8.3

Control signals

CAN_Low, CAN_High, CAN_GND
corresponding to CiA DS 301
Important notice:
Status changes of each of the
4 cams will be transmitted as
emergency objects with the high-
est priority after < 0.5 ms. Hence,
these transducers are specially
suited for time-critical control
tasks.
8.4

Connection to processor

Cable:
twisted-pair, shielded
max. length 2500 m,
stubs max. 0.3 m, Ø 6 to 8 mm
8.5

Included in shipment

Transducer with mounting brackets
➥ ➥ ➥ ➥ ➥ Fig. 3-1 or
8.6

Magnet

(order separate)
Regarding distance, offset, and
dimensions see pages 4 and 5.
Operating temp.
BTL5-P-3800-2
Weight
Housing
BTL5-F-2814-1S
Weight
Housing
BTL5-M-2814-1S ➥ Fig. 3-7
Weight
Housing
Sliding surface plastics
BTL5-N-2814-1S ➥ Fig. 3-7
Weight
Housing
pp
Sliding surface plastics
BTL5-P-3800-2 and
BTL5-F/M/N-2814-1S:
BTL5-P-5500-2
Weight
Housing
BTL5-P-4500-1
Weight
Housing
Operating temp.
➥ ➥ ➥ ➥ ➥ Fig. 4-1
BTL5-P-5500-2 and
BTL5-P-4500-1:
Recommended resolutions
Non-linearity
➥ ➥ ➥ ➥ ➥ Fig. 3-5
Control arm (optional)
BTL2-GS10-_ _ _ _-A
Aluminum, dimensions ➥ ➥ ➥ ➥ ➥ Fig. 3-8
–40 °C to +85 °C
➥ ➥ ➥ ➥ ➥ Fig. 3-2
Various standard lengths LG avail-
able (please specify when ordering)
approx. 12 g
plastics
➥ Fig. 3-6 8.7
approx. 28 g
Connection cable ➥ ➥ ➥ ➥ ➥ Fig. 4-2
plastics
Connectors
approx. 32 g
aluminum, anodized
approx. 35 g
aluminum, anodized
The stated non-linearity of ± 30 µm
is valid when guided exactly with
a constant gap from the profile
within the permissible distance "D".
➥ Fig. 3-3
approx. 40 g
plastics
➥ Fig. 3-4
approx. 80 g
plastics
–40 °C to +60 °C
20 µm, 50 µm or 100 µm
< ± 100 µm
The stated non-linearity of
< ± 100 µm is valid when guided
exactly with a constant gap from
the profile within the permissible
distance "D".

Accessories (optional)

➥ ➥ ➥ ➥ ➥ Fig. 4-4