Publicité
Les langues disponibles
Les langues disponibles
EN
Klemko Techniek B.V.
Nieuwegracht 26
MANUAL
870060 - PIR-HF 240 DUO
870004 - P300-DUO-PROF
NOTE: isolate all connection cables
before installation. Read the
instructions for use carefully.
If in doubt, consult a qualified installer!
DESCRIPTION
The detector should be mounted on the
ceiling or a flat wall. The detection field is
240° with a 16m radius at an installation
height of 2.50m.
After the jumper has been removed, the
relay output is potential free and can be
loaded up to 10A. The relay is controlled
by a micro processor that closes the
relay at the zero crossing. The switch-
off delay is adjustable between 5 sec.
and 30 min. and can be configured as
an impulse sender (t = 1 sec. then 9 sec.
off). The lux value can be set to a fixed
level using the potentiometer or set to
an actual lux value by the learning mode.
The movement sensor can be mounted
either on the ceiling or on a flat wall. The
The ideal mounting height is 2.5 metres.
connector pins ensure quick and correct
If the sensor is higher, the detection
installation of the sensor. The mounting
sensitivity will be reduced.
box has an earth connector avoiding the
The range extends to a maximum radius
need for an extra junction box. The set-
of 16m with a detection angle of 240
tings can be adjusted using the optional
degrees (PIR) and 180 degrees (radar).
remote control or using the potentiom-
Determine the location where the detec-
eters on the head. The sensor head can
tor is to be mounted in or on the ceiling,
be aligned in Pan or Tilt mode to set the
bearing the following in mind:
detection zone.
1. Air ducts: look out for discharge from extractor
hoods, heating vents, tumble driers, etc.
Lens masks for the PIR detection field are
2. Objects that could be moved by air currents such as
supplied as standard.
plants and curtains.
870060 only:
3. Do not point the sensor at other light sources.
4. Do point aim the sensor at highly reflective surfaces
combi movement sensor for cold stores,
such as swimming pools (because of rapid temperature
etc. with PIR and radar detection.
changes).
5. Be aware of where people walk and in what
direction (always try to position the field in such a way
that the walking direction crosses the field instead of
moving straight towards the detector).
6. Do not install the detector on conducting
Guarantee: 24 months after production date provided the product is used as instructed and not opened.
T +31 (0)88 002 3300
SPECIFICATIONS
1.
Mains voltage
220 - 240 V 50/60Hz
Potential-free make contact
Contact
(after removing jumper)
Zero crossing
Yes
2.
Load:
Halogen lamp
Max. 1200 W
3.
Low-voltage halogen
Max. 1000VA / 600 W
Incandescent lamps
2300 W AC
HF fluorescent
Max. 1000 VA / 600 W
(uncompensated)
4.
HF fluorescent
Max. 900 VA / 100 μF
(compensated)
LED with driver
Max. 400 W
Energy-saving lamps
Max. 600 VA / 400 W
L
N
Max. 10A (cosφ=1) 250VAC
HVAC
Max. 5A 30VDC
Max. 3A (cosφ=0.4) 250VAC
PIR: max. R 16 metres forwards
Detection range
HF (870060): 180° max R 16m oval
Time setting
5 sec - 30min.
Lux setting adjustable
5 Lux - ∞
870060: -20° C to +50° C
Temperature
870004: -10° C to +40° C
IP54 (wall-mounted)
IP value
IP55 (ceiling-mounted)
Remote control
870588 (optional)
Standards
CE/TUV
1.5m
POSITIONING THE SENSOR
surfaces.
NL-3763 LB
Soest
www.klemko.nl
INSTALLATION
Mount the junction box on the wall
and wire the terminal block as
shown in the wiring diagram.
Only if a cancel switch is included in
The wires can be routed directly
series with a phase line, can the user
through the cast-in grommets to
bridge the set switch-off delay by inter-
create a waterproof seal.
rupting it with a brief voltage.
Put the switch unit on the junction
box and press it firmly into place.
Fasten the switch unit using 2
When the light is switched off:
screws.
>> turn off the voltage using the cancel
Switch on the voltage and test the
switch >> switch on >> switch off
detection zone.
within 2 sec >> switch on again. To
WIRING DIAGRAM
confirm this command, the detector
will switch the light on for 3 sec >> then
switch off for 2 sec to
Pushbutton
then stay on for 8 hours
(N.C. type)
uninterrupted. Throughout these 8 hours,
jumper
Load
the red LED will light up every 5 sec. Af-
ter 8 hours the detector will automatically
N
L
D1
D2
return to normal mode.
Blue
Brown
Red
Red
Movement sensor
DETECTION
When the light is switched on:
>> turn off the voltage using the cancel
o
o
240
240
switch >> switch on >> >> switch off >>
R3m
switch on within 2 sec. To confirm this
R5m / 360
o
R16m
command, the detector will turn the light
R16m
16m
off for 2 sec and then stay switched on
3m
16m
for 8 hours
uninterrupted. The red LED will light up
every 5 sec throughout these 8 hours.
After 8 hours the detector
will automatically return to normal mode.
At any point in these 8 hours, the user
can return the lighting to automatic mode
by interrupting the voltage briefly (less
than 1 sec) using the cancel switch. To
confirm this command, the detector will
switch the light off for 2 sec and then
return to normal mode.
These settings can also be changed to
constantly on or off using the optional
remote control IR-11 (870588).
The Netherlands
info@klemko.nl
CONSTANTLY ON
Transition from automatic to 8 hours.
The extra radar sensor integrated in the
870060 is able to detect movement
through materials like plastic, wood and
brick. It cannot detect through water or
metal.
The radar sensor has a high degree of
detection reliability and is less sensitive
to temperature fluctuations and other
sources of interference compared to the
PIR sensor.
When choosing a position, remember
that the sensor detects through materi-
als. This increases the likelihood of unin-
tended triggering of the connected load.
DETECTION MATERIALS
MATERIAL
PVC / plastic
Wood
Glass
Brick
Concrete
forced)
Metal
Teaching in actual lux value
By setting the potentiometer lux value
by eye, the learning function is enabled.
The sensor measures the lux value in the
environment and saves it in the memory.
The function can only be used in the
range 5 - 500 lux. A setting of 5 lux is
specified for anything below 5 lux and
the lux value threshold is switched off
above 500 lux.
Note: Do not stand in the vicinity of the
sensor when teaching in. This will have a
significant influence on the value meas-
urement and lead to errors.
The LED integrated in the sensor will
slowly flash for 25 seconds during the
teaching-in process, following which
the light will illuminate for 5 seconds
and then the light will go out. This signal
means that the teaching-in process has
completed successfully.
RADAR DETECTION
870060 only
DETECTION
REDUCTION
ANGLE
Yes
5 - 10 %
Yes
10 - 20 %
Yes
15 - 30 %
Yes, < 30cm
60 - 70 %
No, > 30cm
100 %
(no detection)
(rein-
no
100 %
(no detection)
no
100 %
(no detection)
LUX SETTING
Publicité
