Cooper Lighting Halo RL560 Serie Manuel D'instructions page 3

7. Squeeze the torsion springs together as shown
and install into torsion spring brackets inside
recessed housing (Fig. 10).
7a. If using friction blades, while wearing gloves
squeeze opposing blades together until blades fit
inside housing then carefully insert RL560 into
housing allowing springs to expand to hold RL560
in housing.
8. Carefully route wires into fixture and push module
up flush to ceiling surface.
INSTALLATION INTO HALO ® H27050x,
H550x and H750x SERIES LED
(non-screw base) HOUSINGS
NOTE: May be used to meet California Title 24 and
International Energy Conservation Code High Efficacy
Compliance.
1. Plug module into Halo recessed fixture connector
(Fig.11).
2. Squeeze torsion springs together as shown and
install into torsion spring brackets inside recessed
housing (Fig. 10).
3. Carefully route wires into fixture and push module
up flush to ceiling surface.
REPLACING LED MODULE
1. With fingertips, pull down firmly on trim ring until
module is removed from the housing.
2. Squeeze torsion springs together to remove LED
module. If using friction blades, pull module out of
housing slowly.
3. Disconnect LED module wiring from recessed can
(LED connector or screw-in Edison base).
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting, LLC ("Cooper Lighting") warrants to customers that, for a period of five years
from the date of purchase, Halo RL560 series products will be free from defects in
materials and workmanship. The obligation of Cooper Lighting under this warranty is expressly
limited to the provision of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser's receipt or other proof of date of original purchase
acceptable to Cooper Lighting. This is required before warranty performance shall be rendered.
This warranty does not apply to Cooper Lighting products that have been altered or repaired or
that have been subjected to neglect, abuse, misuse or accident (including shipping damages).
This warranty does not apply to products not manufactured by Cooper Lighting which have
been supplied, installed, and/or used in conjunction with Cooper Lighting products. Damage to
the product caused by replacement bulbs or corrosion or discoloration of brass components
are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL COOPER LIGHTING BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN
CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS;
NOR SHALL THE LIABILITY OF COOPER LIGHTING FOR ANY CLAIMS OR DAMAGE ARISING
OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE,
MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY OF
ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING
PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR
INSTALL FIXTURES.
To obtain warranty service, please contact Cooper Lighting, LLC, at 1-800-334-6871, press
option 2 for Customer Service, or via e-mail ConsumerProducts@cooperlighting.com and
include the following information:
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused.
Cooper Lighting, LLC is not responsible for merchandise damaged in transit. Repaired or
replaced products shall be subject to the terms of this warranty and are inspected when
packed. Evident or concealed damage that is made in transit should be reported at once to
the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@cooperlighting.com.
Fig. 10
ARTÍCULOS NECESARIOS
(se compran por separado)
Destornillador
Guantes (si se utiliza las hojas de fricción)
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Al utilizar el producto, siempre se deben seguir las precauciones básicas, incluído
lo siguiente:
Tenga en cuenta todas las advertencias, incluyendo las advertencias a continuación
Y aquellas incluidas en el producto.
La luminarias (accesorios) empotradas HALO
los requisitos NEC más recientes y están catalogadas por UL/cUL en completo
cumplimiento con UL 1598. Antes de comenzar la instalación de su luminaria
empotrada verifique el código local. Este código fija los estándares de cableados
de su localidad y debe ser estudiado cuidadosamente antes de comenzar.
Fig. 11
Lea y siga estas instrucciones.
Riesgo de incendio. UTILICE CONDUCTORES DE SUMINISTRO QUE SOPORTEN UN
MÍNIMO DE 90°C. Si no está seguro consulte a un electricista.
Riesgo de descarga eléctrica. Para evitar una descarga eléctrica, asegúrese que el
suministro eléctrico esté desconectado en la caja de fusibles o interruptores de
circuito antes de instalar o dar mantenimiento al accesorio.
PRECAUCIÓN
Conecte el accesorio a una fuente de energía de 120 Voltios, 60 Hz. Cualquier
otro tipo de conexión anula la garantía.
El accesorio debe ser instalado por personas con experiencia en cableado
doméstico o por un electricista calificado. El sistema eléctricoy el método de
conexión eléctrica del accesorio debe cumplir con el Código eléctrico nacional
y los códigos locales sobre edificios.
Este dispositivo cumple con parte 15 de las reglas de FFC. SU operación está sujeta
a las siguiente condiciones: (1) Este dispositivo no puede causar interferencia dañina,
y (2) este dispositivo puede recibir interferencia, incluyendo aquella que puede causar
una operación no deseada del dispositivo.
GUARDE ESTAS INSTRUCCIONES Y ADVERTENCIAS.
ALOJAMIENTOS
El RL560 viene con un Conector LED especial para el Cumplimiento del Titulo
24 de California y está homologado por UL para la instalación en alojamientos de LED
Halo
y H550RICAT.
El RL560 también incluye un adaptador de base Edison para adaptar
alojamientos ICAT de base con rosca estándar. El RL560 está homologado y clasificado
por UL para adaptarse en los siguientes alojamientos.
Homologado por UL
Clasificado UL
* Requiere el remplazo de los resortes de torsión con sujetadores de fricción (pida los
†
3
ESPAÑOL
ADVERTENCIA
® empotrados saeries H750ICAT, H750R, H750T, H750TCP, H2750ICAT, H550ICAT,
- HALO : H7ICAT, H7ICT, H7T, H7ICATNB, H7ICTNB, H7TNB, H7UICAT, H7UICT, H7TCP,
®
H7RICAT, H7RICT, H7RT, H27ICAT, H27ICT, H27T, H27RICAT, H27RICT,
H27RT, H5ICAT, H5RICAT, H5T, H5RT, H5TM, H25ICAT
- HALO ® LED Retrofit: ML7BXRFK, ML7E26RFK
- ALL-PRO ™ : EI700, EI700AT, EI700ATNB,EI700U, EI700UAT, EI700NB,EI700R,
EI700RAT, ET700, ET700R, EI2700, EI2700AT, ET2700,EI2700R,
ET2700R, EI500AT, ET500, EI500RAT, ET500R
- Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21, IC21R, IC2, TC2, TC2R, IC20,
IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R
- Lightolier: 1104ICS*, 1104ICR*, 1104SIC*
1004SIC* , 1004SICR*
† †
1104ICX - Requires installation of Halo ML7RAB retrofit adapter band
accessory.
- Capri: CR1, PR1, QL1, R9ASIC, R5*
- Progress: P87-AT*, P86TG
- Lithonia: L7X, L7XP
- Thomas: PS1, R9ASIC/PS9RM
- Prescolite: IBXS
- Commercial Electric: C7ICA (H3), H18
- Elco: (HL7ICA) EL7ICA
sujetadores por separado: RL56CLIP).
Los alojamientos poco profundos Lightolier requieren que la lata se eleve a la
posición más alta, y que dos lengüetas del portalámparas se doblen hacia afuera.
® están diseñadas para cumplir con
, 1104SICR* , 1004ICS*, 1004ICR*,
† †