Publicité
Klebedichtung, Abb. 4:
Die Klebedichtung zentral auf dem Absatz der Arbeitsplatte
anbringen.
Einbau des Geräts, Abb. 5/6/7
Hinweis: Zum Einbauen des Kochfeldes Schutzhandschuhe ver-
wenden. Die nicht sichtbaren Flächen können scharfe Kanten
aufweisen.
Das Gerät gleichmäßig in den zugeschnittenen Bereich setzen.
1.
Überprüfen, ob das Kochfeld auf gleicher Höhe mit der
2.
Arbeitsplatte liegt. Falls das Kochfeld nicht ausgerichtet wer-
den kann, die mitgelieferten Verankerungen nur an den not-
wendigen Punkten anbringen und vorsichtig festziehen,
(Abb. 5).
Hinweis: Keine elektrischen Schraubendreher verwenden.
Gerät an das Netz anschließen und Funktion prüfen.
3.
– Spannung siehe Typenschild.
– Nur gemäß Anschlussbild anschließen (Abbildung 7).
1. Braun
2. Schwarz
3. Blau
4. Grau
5. Grün-gelb
Hinweis: Je nach Anschlussart muss eventuell die Anordnung
der vom Werk gelieferten Klemmen verändert werden.
Vor dem Abdichten (Abb. 6) unbedingt einen Betriebstest
4.
durchführen!
Den Abstand zwischen den Bereichen mit geeignetem hitzebe-
ständigen Silikon (z. B. Novasil
Die hermetische Dichtung mit einem vom Hersteller empfohle-
nen Produkt glätten. Die Angaben auf dem Silikon beachten.
Das Gerät nicht in Betrieb nehmen, bevor das Silikon vollstän-
dig getrocknet ist (je nach Umgebungstemperatur, mindestens
24 Stunden).
Geeignetes Silikon kann bei unserem Kundendienst erworben
werden.
Achtung!
Wird bei Arbeitsplatten aus Naturmarmor ungeeignetes Silikon
verwendet, können Verfärbungen entstehen, die nicht entfernt
werden können.
Ausbau des Geräts
Das Gerät von der Stromzufuhr trennen.
Die Silikondichtung der gesamten Umrandung des Kochfelds
mit einem geeigneten Werkzeug entfernen.
Die Halterungen entfernen.
Entnehmen Sie das Kochfeld, indem Sie von unten dagegen
drücken.
Achtung!
Schäden am Gerät! Versuchen Sie nicht, das Gerät durch
Hebeln von oben zu entnehmen.
en
Ú
Installation instructions
Important notes
Safety: Safety in use is only guaranteed if the technical
installation of the hob has been carried out correctly and in
accordance with the assembly instructions. The installation
technician shall be liable for any damage caused as a result of
unsuitable installation.
Electric connection: Only by an authorised specialist
technician. The guidelines set out by the local electricity provider
must be observed.
Type of connection: The appliance falls under protection class I
and can only be used in combination with a grounding
conductor connection.
The manufacturer accepts no responsibility for any malfunction
or damage caused by incorrect electrical installations.
Installation: The appliance must be connected to a fixed
installation and the means of disconnecting it from the fixed
installation must be installed according to the installation
instructions.
Built-in assembly under worktop: hobs should only be installed
above a drawer or forced ventilation ovens of the same
specification. Refrigerators, unventilated ovens and washing
machines may not be installed beneath the hob.
S70, Ottoseal
S70) abdichten.
®
®
Power cable: Do not tie the power cable or pass it along sharp
edges. If there is an oven installed below, pass the cable along
the rear corners of the oven to the connection box. It must be
positioned so that it does not touch any of the hot parts of the
hob or the oven.
Hob: flat, horizontal, stable. Follow the hob manufacturer's
instructions.
Warranty: an unsuitable installation, connection or assembly will
invalidate the product warranty.
Note: Any change to the appliance's interior, including changing
the power cable, must only be performed by specially trained
members of the Technical Assistance Service.
Preparation of assembly units, figures 1/2/3/4
Built-in kitchen units: Minimum temperature resistance of
90°C.
Gap: Remove any shavings after performing cutting work.
Cut surfaces: Seal with heat resistant material.
The appliance can be mounted on the following heat and water
resistant worktops:
Marble, natural stone worktops
■
Synthetic worktops
■
Solid wood worktops: only according to the manufacturer of
■
the worktop (sealing of cutout edges)
Assembly with other types of worktops: only according to the
■
manufacturer of the worktop
Note: All worktop cutout work must be carried out by a
specialised service according to the assembly drawings. The
cutout must be clean and precise, as the cut edge will be visible
on the surface. Clean and degrease the cutout edges using a
suitable cleaning product (check the silicone manufacturer's
indications).
Assembly over drawer, figure 2a
Hob: must have a minimum thickness of 30 mm.
The distance between the top of the hob and the top of the
drawer must be 70 mm.
Assembly over oven, figure 2b
Hob: must have a minimum thickness of 30 mm.
Note: If the distance between the hob and oven must be
increased, refer to the installation instructions for the oven.
Ventilation: The distance between the oven and the hob must be
at least 5 mm.
Ventilation, figure 3
Ventilating the hob requires:
an opening on the upper part of the kitchen unit's rear wall
■
(figure 3a).
a separation between the rear part of the kitchen unit and
■
kitchen wall (figure 3b).
If the interior width of the kitchen unit is less than 880 mm, a
■
cut must be made in the side walls (figure 3c).
Adhesive seal, figure 4:
Adhere the adhesive seal to the stepped rim of the worktop.
Installing the appliance, figures 5/6/7
Note: Wear protective gloves to fit the hob. The non-visible
surfaces may have sharp edges.
Insert the appliance uniformly in the cutout.
1.
Check that the hob is flush with the worktop. If the hob is not
2.
flush, install the anchoring devices supplied only in the points
necessary and tighten them carefully, (figure 5).
Note: Do not use electric screwdrivers.
Connect the appliance to the mains and check that it works
3.
correctly.
– See the rating plate for the voltage.
– Only connect the appliance in accordance with the
connection diagram (Fig. 7).
1. Brown
2. Black
3. Blue
4. Grey
5. Green-yellow
Note: Depending on the type of connection, the arrangement of
the clamps supplied by the factory may need to be changed.
Publicité
