Renkforce 1007066 Mode D'emploi page 3

G Operating instructions
Digital radio wall clock Slim
Item no. 1007066 (white)
Item no. 1007068 (black)
Intended use
This product is intended for displaying the time and the date. Furthermore, the room temperature
is shown on the display.
The time is set automatically using an integrated DCF receiver.
Any use other than that described above could lead to damage to this product and involves the risk
of short circuits, fire, electric shock, etc.
No part of the product may be modified or converted.
The safety instructions must be observed at all times.
This product complies with the applicable national and European requirements. All names of com-
panies and products are the trademarks of the respective owners. All rights reserved.
Contents
• Radio wall clock
• Operating instructions
Explanation of the symbols
This symbol indicates specific risks associated with handling, function and use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
First, read the complete operating manual carefully, as it contains important informa-
tion about the proper operation.
The warranty will be void in the event of damage caused by failure to observe these
safety instructions! We do not assume any liability for any resulting damage!
We shall not accept liability for damage to property or personal injury caused by in-
correct handling or non-compliance with the safety instructions! The warranty will be
void in such cases!
• For safety reasons, any unauthorised conversion and/or modification to the product
is not permitted.
• Do not expose the product to high temperatures, strong vibrations or heavy mechani-
cal loads.
• If you have any doubts about the correct operation, or the safety of the product,
please consult a specialist.
• This product is not a toy and must be kept out of the reach of children. Use the prod-
uct only out of the reach of children; the product contains parts and batteries that
can be swallowed.
• Do not leave packaging material unattended. It may become a dangerous plaything
for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
• Also observe any further safety instructions in the individual sections of this operat-
ing guide.
Notes on Batteries and Rechargeable Batteries
• Batteries/rechargeable batteries must be kept out of the reach of children.
• Do not leave batteries/rechargeable batteries lying around; there is a risk that they
could be swallowed by children or pets. If they are swallowed, consult a doctor im-
mediately.
• Leaking or damaged normal/rechargeable batteries in contact with the skin can
cause acid burns; therefore, use suitable safety gloves.
• Normal/rechargeable batteries may not be short-circuited, opened or thrown into
fire. There is a risk of explosion!
• Do not recharge normal, non-rechargeable batteries, there is a risk of explosion!
Only charge rechargeable batteries that are intended for this purpose; use a suitable
battery charger.
• Check that the polarity is correct when inserting the battery/rechargeable battery
(pay attention to plus/+ and minus/-).
Features
• Simultaneous display of time, month, date, weekday and room temperature
• Large LC display
• 12h or 24h display format can be selected
• Weekday displays in 4 languages
• Can be used as a table or wall clock
Controls and Parts
(1) RESET button
(2) "+" button
(3) SET/WAVE button
(4) "-" button
Installation/Set-up
• The radio-controlled wall clock can be placed onto furniture or attached to the wall.
• To set up the clock, fold out the support and place the clock on a level surface.
• Protect valuable furniture surfaces by using an appropriate underlay; otherwise, it may cause
scratches.
• There is a suspension eye on the back of the casing for wall mounting.
• Secure the clock in place with a screw that protrudes a few millimetres from the wall. Then hang
the clock on the screw head with the suspension eye.
To ensure correct DCF reception, the radio-controlled wall clock should not be placed
next to electronic devices, cables, metal parts, etc.
Inserting/Replacing Batteries/Rechargeable Batteries
• Open the battery compartment on the rear of the housing and insert three new batteries of type
AAA/Micro with the correct polarity.
• The correct polarity is indicated in the battery compartment.
• After inserting the batteries, the radio tower symbol starts to flash in the LC display.
• The radio wall clock now attempts to receive a DCF signal (see also chapter "DCF reception").
• Close the battery compartment again.
• The batteries need changing, if the display contrast diminishes or the LC display no longer func-
tions.
The use of rechargeable batteries is possible. However, the lower operating voltage
(rechargeable battery = 1.2 V, battery 1.5 V) and lower capacity will reduce the operat-
ing time.
If there is no correct indication in the LC display, please press the RESET button on the
back of the case to activate the reset function. Hereby, the internal processor is reset
and is able to function properly again.