Lights - Kenmore 106.5178 Série Guide D'utilisation Et D'entretien

Ultra Satin™ (stainless look) finish: Wash with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners designed for
stainless steel. Dry thoroughly with a soft cloth.
Stainless steel finish: Wash with a clean sponge or soft cloth
and a mild detergent in warm water. Do not use abrasive or
harsh cleaners. Dry thoroughly with a soft cloth.
To keep your stainless steel refrigerator looking like new
and to remove minor scuffs or marks, it is suggested that
you use the manufacturer's approved Stainless Steel
Cleaner and Polish. To order the cleaner, see
"Accessories."
IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to
come into contact with any plastic parts such as the trim
pieces, dispenser covers or door gaskets. If unintentional
contact does occur, clean plastic part with a sponge and
mild detergent in warm water. Dry thoroughly with a soft
cloth.
5. If your model has a touch screen display on the dispenser
panel, clean the screen using a soft, lint-free cloth. Mix a
mild detergent with water, then use the mixture to dampen
the cloth and gently wipe the screen.
To avoid unintentionally changing settings, make sure the
refrigerator is unplugged or the power is disconnected
before wiping the screen.
Do not over-saturate the cloth. Do not spray or wipe
liquids directly onto the screen. Do not use abrasive or
harsh cleaners such as window sprays, scouring
cleansers, flammable fluids, cleaning waxes,
concentrated detergents, nail polish remover, bleaches
or cleansers containing petroleum products. Do not use
paper towels, scouring pads, or other harsh cleaning
tools. These can scratch or damage materials.
6. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic
in the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
Remove the base grille. See "Base Grille" graphic or
"Base Grille" section.
Use a vacuum cleaner with a soft brush to clean the
grille, the open areas behind the grille and the front
surface area of the condenser.
Replace the base grille when finished.
7. Plug in refrigerator or reconnect power.
IMPORTANT: The light bulbs in both the refrigerator and freezer
compartments of your new refrigerator may use LED
technology. If the lights do not illuminate when the refrigerator
and/or freezer door is opened, call for assistance or service. In
the U.S.A. and Canada, call 1­800­4­MY­HOME
(1­800­469­4663).
Light Styles:
The dispenser lights are mini LEDs that cannot be changed.
The interior lights vary by model.
Some models have mini LEDs that cannot be changed.
Some models have full-size LED bulbs that can be
changed. To order replacement LED bulbs, call
1­800­4­MY­HOME (1­800­469­4663) in the U.S.A. and
Canada.
Part Number
W10574850A
(2.0 watts)
NOTE: Some LED replacement bulbs are not
recommended for wet/damp environments. The
refrigerator and freezer compartments are considered
to be wet/damp environments. If using an LED bulb
other than the part numbers recommended above, read
and follow all instructions on the replacement bulb's
packaging before installing it.
Some models have incandescent 40­watt bulbs that can
be changed.
NOTE: Not all replacement bulbs will fit your
refrigerator. Do not use an incandescent bulb in excess
of 40 watts.

Lights

Part Number
W10565137A
(3.6 watts)
15