Publicité
Liens rapides
PJMPRO
Projector Mount with Micro Adjustments
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D' INSTRUCTIONS
b
r
a
n
d
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
Projector Mount
Max weight: 50lbs
V1
P1
Publicité
Manuels Connexes pour BRKT Brand PJMPRO
Sommaire des Matières pour BRKT Brand PJMPRO
- Page 1 PJMPRO Projector Mount with Micro Adjustments INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MANUEL D’ INSTRUCTIONS CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! Projector Mount Max weight: 50lbs...
- Page 2 Tampoco prevé todas las posibles contingencias relacionadas con la instalación o el uso de este producto. La inf ormación que contiene este documento queda sujeta a cambio sin aviso previo o compromiso alguno. BRKT BRAND no ofrece ninguna garantía, ni expresa ni implícita, respecto de la información aquí incluida. BRKT BRAND no se responsabiliza de la precisión de la información provista en este documento, ni tampoco de que sea completa o suficiente.
- Page 3 HARDWARE PRODUCT NUMBERS leg post leg post leg post leg post leg post Pinned Hex Screw Rectangular Nut M3x10 M4x10 M5x10 M6x10 M5x20 M6x12 8mm lag bolt 8mm washer Allen Wrench Allen Wrench Pinned Allen Wrench Set Screws 2.5mm 2.5mm PRODUCT COMPONENT PARTS P-A –...
- Page 4 STEP 1- LOOSEN HALF WAY STEP 2- REMOVE THE CEILING PLATE AND THE COVER...
- Page 5 STEP 3- FIND STUD AND MARK EDGE AND CENTER LOCATIONS. STEP 4- DRILL PILOT HOLE AND MOUNT CEILING PLATE. Wood Pilot Pilot Hole Size Pilot Drill Depth 7/32” inch 2.75 inch 5.5 mm 70 mm...
- Page 6 STEP 5A- ATTACH THE ARTCULATION UNIT AT THE CEILING PLATE STANDARD CEILING INSTALLATION IMPORTANT! TIGHTEN UNTIL SNUG MINIMUM 2 TURN ENGAGEMENT STEP 5B- ATTACH THE ARTCULATION UNIT AT THE CEILING PLAT WITH AN EXTENTED NPT PIPE. DROP CEILING INSTALLATION 1-1/2” NPT PIPES (NOT INCLUDED) IMPORTANT! TIGHTEN UNTIL SNUG...
- Page 7 STEP 6- ASSEMBLE THE SET SCREW TO FIX THE MOUNT. Do not over-tighten STEP 7- ATTACH THE PROJECTOR LEGS AT THE PROJECTOR PLATE.
- Page 8 STEP 8- ATTACH THE PROJECTOR AT THE MOUNT. Front A – E STEP 9- LIFT AND HANG THE PROJECT. NOTE: USE CAUTION! YOUR PROJECTOR ASSEMBLY IS NOT YET SECURED TO THE CEILING PLATE...
- Page 9 STEP 10- FIX THE PROJECTOR. LOCK NOT INCLUDED STEP 11A- ADJUST THE MOUNT TO THE BEST FEATURE. YAW ADJUSTMENT ROLL ADJUSTMENT +/- 5° +/- 180° FRONT REAR PITCH ADJUSTMENT +/- 20°...
- Page 10 STEP 11B- ADJUST THE MOUNT TO THE BEST FEATURE. Do not over-tighten...
- Page 11 STEP 12A- QUICK ACCESS PROJECTOR SERVICING LOCK NOT INCLUDED STEP 12B- QUICK ACCESS PROJECTOR SERVICING Cable Management...
- Page 12 This warranty applies to US Residents who purchase from an authorized BRAND Dealer. BRKT BRAND are covered againse defects in materials and workmanship for 5 years. BRKT BRAND will repair or replace the defective component or product, at its sole discretion. Failure to follow product care instructions from BRKT BRAND will result in void of warranty.