Sommaire des Matières pour BRKT Brand BRKT ARM2346HD
Page 1
BRKT ARM2346HD Medium Full Motion Flat Panel Mount INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MANUEL D’ INSTRUCTIONS CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! Max Screen Size: 46” Max Weight: 80 LBS...
Page 2
Tampoco prevé todas las posibles contingencias relacionadas con la instalación o el uso de este producto. La inf ormación que contiene este documento queda sujeta a cambio sin aviso previo o compromiso alguno. BRKT BRAND no ofrece ninguna garantía, ni expresa ni implícita, respecto de la información aquí incluida. BRKT BRAND no se responsabiliza de la precisión de la información provista en este documento, ni tampoco de que sea completa o suficiente.
Page 3
MONITOR PLATE AND ADAPTERS Use diagrams to determine which mounting configuration is needed to attach Monitor Plate (with or without adapters) to the back of flat panel. Please check flat panel wall mounting compatibility before proceeding with installation. Pay attention to below the correct installation pattern of adapters A and B.Confuse them may cause TV enable to be mounted correctly.
Page 4
HARDWARE PART NUMBERS M4 x 12 M5 x 12 M6 x 15 M8 x 15 M4 x 25 M5 x 25 M6 x 25 M8 x 25 STEEL SQUARE 8 mm LAG PHILLIPS STEEL ANCHOR END COVER WASHER WASHER SPACER SCREWS BOLTS WASHER...
Page 5
STEP 1- REMOVE MONITOR PLATE FROM MOUNT Remove and save Phillips head screws and washers. Screws and washers will be used to reattach monitor plate in step 4. STEP 2A- MONITOR PLATE ATTACHMENT Connect monitor plate to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur...
Page 6
STEP 2B- MONITOR ADAPTERS ATTACHMENT TO MONITOR PLATE Connect monitor plate with adapters to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur STEP 2C- CURVED BACK FLAT PANEL (MONITOR PLATE) Connect monitor plate to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur 5mm spacers to be used when back of panel is curved or when...
Page 7
STEP 2D- USE M8 STEEL WASHER IF THE PHILLIPS SCREWS FROM THE MONITOR KIT ARE TOO LONG Diagrams show three options for using additional washers if hardware screws are too long to properly tighten into back of flat panel television. B or C B or C B or C...
Page 8
STEP 3A- WOOD STUD (CONCRETE INSTALLATION SKIP TO 3B) Find stud and mark edge and center locations Ubique el panel y marque las ubicaciones de los bordes y el centro. DRILL BIT Repérez l'emplacement d'une poutre, puis marquez l'emplacement des bords et du centre de cette poutre. NOT INCLUDED STEP 3A- DRILL PILOT HOLES AND MOUNT WALL PLATE Mount wall plate...
Page 9
STEP 3 B – SOLID CONCRETE Drill pilot hole Solid Concrete Realice el agujero piloto Concreto sólido Percez le trou de guidage Béton massif DRILL BIT NOT INCLUDED 3/8” STEP 3B – DRILL PILOT HOLE AND MOUNT WALL PLATE Slide plastic end cap on top and bottom of wall plate...
Page 10
STEP 4- ATTACH PANEL TO MOUNT Hang with monitor attached Heavy, Assistance Cuelgue con el monitor adherido. Required Accrochez avec le moniteur installé. TRES LOURD ! Cette etape requiert deux personnes !PESADO! Necesitara ayuda para realizar esta operacion Attach the covers to the wall plate ARM ASSEMBLY, LEVEL, AND TILT...
Page 11
This warranty applies to US Residents who purchase from an authorized BRKT BRAND Dealer. BRKT BRAND are covered againse defects in materials and workmanship for 5 years. BRKT BRAND will repair or replace the defective component or product, at its sole discretion. Failure to follow product care instructions from BRKT BRAND will result in void of warranty.