F.F. Group MX 850 PLUS Notice Originale page 8

8 | English
TECHNICAL DATA
Article Number
Model
Rated voltage
Frequency
Rated power input
No-load speed
Tool holder
Size of accessory
Weight
Sound emission values determined according
to EN 60745-1
Typically the A-weighted noise levels of the product
are:
Sound pressure level
Sound power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to
EN 60745-1
Vibration level max:
a
h ,HD
K
IDENTIFICATION
1. ON/OFF switch
2. Lock-on button for On/Off switch
3. Speed control wheel
4. Drive spindle
5. Mixer paddle
6. Auxiliary handle
ASSEMBLY
Before any work on the machine itself,
pull the mains plug.
CHANGING THE TOOL
MIXER PADDLE WITH MALE THREAD, SIZE M14
Screw the mixer paddle 5 into the drive spindle 4. To
do so, hold the drive spindle 4 using an open-ended
spanner, and use a second open-ended spanner to
tighten the mixer paddle 5. The mixer paddle is dis-
assembled in reverse order.
SWITCHING ON AND OFF
To start the machine, press the On/Off switch 1
and keep it pressed. Press the lock-on button 2
to lock the pressed on/off switch 1.
To switch off the machine, release the On/Off
switch 1 or when it is locked with the lock-on
button 2, briefly press the On/Off switch 1 and
43 280
MX 850 PLUS
V 230-240
Hz 50
W 850
min 180-700
-1
M14
Ø mm 120x60
kg 3,6
dB(A) 87,4
dB(A) 98,4
dB 3
(triax vector sum)
h
m/s 1,916
2
m/s 1,5
2
then release it. To save energy, only switch the
power tool on when using it.
WORKING ADVICE
Avoid splashing around the material being
f
stirred. Otherwise, you could slip and lose control
over the power tool.
Avoid continuous operation of the power tool
f
at reduced speed. Otherwise the motor of the
power tool could overheat.
Selection of the mixer paddle is dependent on the
material that is to be stirred.
For materials with low viscosity, e.g. emulsion paint,
varnishes, adhesive, grouting compound, cement
slurry, use a mixer paddle with a left-hand spiral.
The material is moved from the top downwards in a
mixer paddle with a left-hand spiral. The mixer pad-
dle is pushed upwards. Materials with low viscosity
are mixed in a way which minimizes splattering.
For materials with high viscosity, e.g. plaster, con-
crete, cement, screed, filler, epoxy resin, use a
mixer paddle with right-hand spiral. The material is
moved from the bottom upwards in a mixer paddle
with a right-hand spiral. The mixer paddle works its
way into the mixture. Materials with high viscosity
are mixed thoroughly.
While mixing, move the power tool in an up and
down motion.
Clean the mixer paddle after use.
Store the power tool in a safe place. Ensure that
f
it cannot fall over. Otherwise, the machine may
become damaged.
MAINTENANCE AND INSPECTION
Keep the machine and mixer tool clean.
f
The machine's internal components must be
f
kept free of foreign particles. When using the
machine always check, that the ventilation slots
are not covered.
Special maintenance of the machine is not re-
f
quired, however wear parts (f.i. carbon brushes)
should be checked occasionally. Maintenance or
repairs must be carried out only by authorized
service center.
Use original spare parts only.
f
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste. Machine, accessories and pack-
aging should be sorted for environment -
friendly recycling. The plastic components
are labeled for categorized recycling.
GUARANTEE
This product is warranted in accordance with the
legal/country specific regulations, effective from
the date of purchase by the first user. Damage
attributable to normal wear and tear, overload
or improper handling will be excluded from the
guarantee. In case of a claim, please send the ma-
chine, completely assembled, to your dealer or
the service Centre for electric power tools.
MX 850 PLUS