F.F. Group MX 1200 PRO Notice Originale page 8

8 | English
Tool holder
Size of accessory
Weight
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h ,HD
K
IDENTIFICATION
1. ON/OFF switch
2. Lock-on button for On/Off switch
3. Rubber feet
4. Speed selector knob
5. Drive spindle
6. Handle (insulated gripping surface)
7. Ventilation cover
8. Mixer paddle
ASSEMBLY
Before any work on the machine itself,
pull the mains plug.
CHANGING THE TOOL
MIXER PADDLE WITH MALE THREAD, SIZE M14
Screw the mixer paddle 8 into the drive spindle 5. To
do so, hold the drive spindle 5 using an open-ended
spanner, and use a second open-ended spanner to
tighten the mixer paddle 8. The mixer paddle is dis-
assembled in reverse order.
SWITCHING ON AND OFF
To start the machine, press the On/Off switch 1
and keep it pressed. Press the lock-on button 2 to
lock the pressed on/off switch 1.
To switch off the machine, release the On/Off
switch 1 or when it is locked with the lock-on but-
ton 2, briefly press the On/Off switch 1 and then
release it. To save energy, only switch the power
tool on when using it.
INFINITELY ADJUSTABLE SPEED SETTING
Two rpm ranges can be pre-selected with the
speed selector switch 4. The necessary speed de-
pends on the type of the material mixed and it is
recommended to verify it by a practical test.
M14 M14
Ø mm 140x68 140x68
kg 5,9
dB(A) 94 87,6
dB(A) 105 98,6
dB 3
(triax vector sum)
h
m/s 4,09 5,187
2
m/s 1,5
2
WORKING ADVICE
Avoid splashing around the material being
f
stirred. Otherwise, you could slip and lose con-
trol over the power tool.
5,9
Avoid continuous operation of the power tool
f
at reduced speed. Otherwise the motor of the
power tool could overheat.
Selection of the mixer paddle is dependent on the
material that is to be stirred.
For materials with low viscosity, e.g. emulsion paint,
varnishes, adhesive, grouting compound, cement
slurry, use a mixer paddle with a left-hand spiral. The
material is moved from the top downwards in a mix-
3
er paddle with a left-hand spiral. The mixer paddle
is pushed upwards. Materials with low viscosity are
mixed in a way which minimizes splattering.
For materials with high viscosity, e.g. plaster, con-
crete, cement, screed, filler, epoxy resin, use a mixer
paddle with right-hand spiral. The material is moved
from the bottom upwards in a mixer paddle with a
right-hand spiral. The mixer paddle works its way
into the mixture. Materials with high viscosity are
1,5
mixed thoroughly.
While mixing, move the power tool in an up and
down motion.
Clean the mixer paddle after use.
Store the power tool in a safe place. Ensure
f
that it cannot fall over. Otherwise, the machine
may become damaged.
MAINTENANCE AND INSPECTION
Keep the machine and mixer tool clean.
f
The machine's internal components must be kept
f
free of foreign particles. When using the machine
always check, that the ventilation slots are not
covered.
Special maintenance of the machine is not re-
f
quired, however wear parts (f.i. carbon brushes)
should be checked occasionally. Maintenance or
repairs must be carried out only by authorized
service center.
Use original spare parts only.
f
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of dispos-
ing as waste. Machine, accessories and
packaging should be sorted for envi-
ronment - friendly recycling. The plastic
components are labeled for categorized
recycling.
GUARANTEE
This product is warranted in accordance with the
legal/country specific regulations, effective from
the date of purchase by the first user. Damage
attributable to normal wear and tear, overload or
improper handling will be excluded from the guar-
antee. In case of a claim, please send the machine,
completely assembled, to your dealer or the ser-
vice Centre for electric power tools.
MX 1200 PRO | MX 1600 PRO