Matco Tools MT1835 Instructions De Fonctionnement page 3

air supply
Tools of this class operate on a wide range of air pressures. It is recommended
that air pressure of these tools measures 90 PSI at the tool while running free.
Higher pressure and unclean air will shorten tool life because of faster wear
and may create a hazardous condition.
Water in the air line will cause damage to the tool. Drain the air tank
daily. Clean the air inlet filter screen on at least a weekly schedule. The
recommended hook-up procedure can be viewed in Figure 1.
The air inlet (Figure 2), used for connecting air supply, has standard 1/4" NPT
American Thread.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D. and
fittings should have the same inside dimensions.
Whip Hose
Do Not Install
Quick Coupling
Nipple
Here
Quick Coupler
Leader Hose
WarranTy
Matco warrants its air tools for a period of 1 year to the consumer. We will
repair any MT Series air tool covered under this warranty which proves to
be defective in material or workmanship during the warranty period. In order
to have your tool repaired, return the tool to either of the Matco Authorized
Warranty Centers listed below, freight prepaid. Please include a copy of your
proof of purchase and a brief description of the problem. The tool will be
inspected and if any part or parts are found to be defective in material or
workmanship, the tool will be repaired free of charge and returned to you
freight prepaid.
This warranty gives you specific rights. You may also have other rights which
vary from state to state.
The foregoing obligation is Matco's sole liability under this or any implied
warranty and under no circumstances shall Matco be liable for any incidental
or consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or exclusion may
not apply to you.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
MT1835
MT1835 1/4" Heavy Duty Air Ratchet
feaTures
• Small compact tool, great for body repair and under dash work
• Patented built-in grease fitting for greater durability and longer life
• Forged chrome molly ratchet yoke for great durability and strength
• Very small head design (1" wide) for great access almost anywhere
• Overall length of 6-5/8" for unmatched access in tight work spaces
Air Supply
Filter
Nipple
Regulator
Oiler
Drain Daily
fig. 1
TrouBleshooTing
Other factors outside the tool may cause loss of power or erratic action.
Reduced compressor output, ex c es s ive drain on the air line, moisture or
restrictions in air pipes or the use of hose connections of improper size
or poor conditions may reduce air supply. Grit or gum deposits in the tool
may cut power and may be corrected by cleaning the air strainer and flushing
out the tool with gum solvent oil or an equal mixture of SAE #10 and kerosene.
If outside conditions are in order and tool continues to perform erratically,
disconnect tool from hose and take tool to your nearest au t ho r ized service
center.
luBricaTion
Lubricate the air motor daily with quality air tool oil. If no air line oiler is
used, run a teaspoon of oil through the tool. The oil can be squirted into the
tool air inlet or into the hose at the nearest con n ec t ion to the air supply, then
run the tool. The amount of oil to be used is 1 ounce. Overfilling will cause
a re d uc t ion in the power of the tool. Grease fitting on yoke occasionally to
ensure proper lubrication of the ratchet mechanism.
MaTco air coMMand
Tool Repair SV
1330 Commerce Dr.
Stow, OH 44224
(800) 433-7098
discounT Tool repair
3433 Losee Rd. #1
North Las Vegas, NV 89030
(702) 657-6570
3
AIR INLET
fig. 2
Rev. 06/18/08