Instruction Manual - Makita HR2652 Manuel D'instructions

Model HR2653
Work mode Vibration
emission
2
Hammer 11.5 m/s
drilling into
concrete
(a )
h, HD
2
Chiselling func- 9.0 m/s
tion with side
grip (a )
h, Cheq
2
Drilling into 2.5 m/s
metal (a )
h, D
Model HR2653T
Work mode Vibration
emission
2
Hammer 11.5 m/s
drilling into
concrete
(a )
h, HD
2
Chiselling func- 9.0 m/s
tion with side
grip (a )
h, Cheq
2
Drilling into 2.5 m/s
metal (a )
h, D
Model HR2663
Work mode Vibration
emission
2
Hammer 9.5 m/s
drilling into
concrete
(a )
h, HD
2
Chiselling func- 6.0 m/s
tion with side
grip (a )
h, Cheq
2
Drilling into 2.5 m/s or
metal (a ) less
h, D
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
Uncertainty (K) Applicable
standard
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-1
Uncertainty (K) Applicable
standard
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-1
Uncertainty (K) Applicable
standard
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-1
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
ROTARY HAMMER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can
1.
cause hearing loss.
2. Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Wear a hard hat (safety helmet), safety glasses and/
4.
or face shield. Ordinary eye or sun glasses are NOT
safety glasses. It is also highly recommended that
you wear a dust mask and thickly padded gloves.
5. Be sure the bit is secured in place before operation.
6. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
In cold weather or when the tool has not been
7.
used for a long time, let the tool warm up for
a while by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
8. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
9. Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
13. Do not touch the bit, parts close to the bit, or
workpiece immediately after operation; they
may be extremely hot and could burn your skin.
14. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
15. Do not touch the power plug with wet hands.
SAVE THESE INSTRUCTIONS.
9 ENGLISH