Télécharger Imprimer la page

Sunex Tools SX108A Instructions De Fonctionnement page 3

Clé à cliquet pnuematique à carré d'entrainement 3/8 po

Publicité

Les langues disponibles

Les langues disponibles

Warning Information • Operating Instructions • Parts Break down
Air Supply...
Tools of this class operate on a wide range of air pres s ures. It is
recommended that air pres s ure of these tools mea s ures 90 PSI at the
tool while running free. Higher pres s ure (over 90 psig; 6.2 bar) raises
per f or m ance beyond the rated capacity and will short e n tool's life.
Always use clean, dry air. Dust, corrosive fumes and/or water in the air
line will cause damage to the tool. Drain the air tank daily. Clean the
air inlet filter screen on at least a weekly schedule. The rec o m m end e d
hookup pro c e d ure can be viewed in figure 1.
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no air line oiler
is used, run 1/2 ounce of air tool oil through the tool by squirting oil
into the tool's air inlet or into the nearest connection to the air inlet,
reconnecting air supply, and then running tool. Do not use more than
1/2 ounce of oil, as overfilling will reduce the performance of the tool.
Troubleshooting...
Other factors outside the tool may cause loss of power or erratic action.
Reduced compressor output, excessive drain on the air line, moisture or
restrictions in air pipes or the use of hose connections of improper size
or poor conditions may reduce air supply. Grit or gum deposits in the
tool may cut power and may be corrected by cleaning the air strainer
and flushing out the tool with gum solvent oil or an equal mixture of
SAE #10 and kerosene. If outside conditions are in order, disconnect tool
from hose and take tool to your nearest authorized service center.
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS ® BRANDED
PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools ® branded products which fail to give satisfactory service due to defective workmanship
or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific product. This product carries a
ONE-YEAR warranty. During this warranty period, Sunex Tools ® will repair or replace at our option any part or unit which proves to be defective in material or
workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement made
by anyone other than Sunex Tools ® or its authorized warranty service centers. The foregoing obligation is Sunex Tools ® sole liability under this or any implied
warranty and under no circumstances shall we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Return equipment or parts to Sunex Tools ® , or an authorized warranty service center, transportation prepaid. Be certain to include your name and address,
evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools ® . This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools ® products regardless of whether or not the product is
still covered by a warranty plan.
SHIPPINg ADDRESS: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
MAILINg ADDRESS: Sunex Tools • P.O. Box 1233 • Travelers Rest, SC 29690
SX108A: Parts Breakdown & Operating Manual
Operation...
This ratchet wrench is rated at 3/8" USS bolt size. Rating must be
down graded for spring U bolts, tie bolts, long cap screws, double
depth nuts, badly rusted conditions and spring fasteners as they
absorb much of the impact power. When possible, clamp or wedge
the bolt to prevent springback.
NOTE: Actual torque on a fastener is directly related to joint
hardness, tool speed, condition of socket and the time the tool is
allowed to impact.
Use the simplest possible tool-to-socket hook up. Every connection
absorbs energy and reduces power.
NOTE: Soak rusted nuts in penetrating oil and break rust seal
before removing with impact wrench. If nut does not start to move
in three to five seconds use a larger size impact wrench. Do not
use impact wrench beyond rated capacity as this will drastically
reduce tool life.
3
Rev. 06/30/10

Publicité

loading