Martin Logan Motion Vision X Guide De Démarrage Rapide

contents
60 inch
wall
(152 cm)
bracket
78 inch
(198 cm)
remote
control
top panel controls
[volume up]
[previous [next
input] input]
[mute] [volume down]
standard
controls
[wi-fi setup & status:
WPS setup: press 3 seconds,
access point setup:
press 8 seconds ]
[power on]
[access menu:
[power off:
press center button power
press 2 seconds ]
2 seconds ]
and menu
access
[up]
[left] [right]
[enter]
[down]
menu
controls
connections
Multi-Channel Audio/Video Sources:
Blu-ray, DVD, Game Console,
Cable Box, Satellite Tuner, Etc.
wall mount installation template
[connect to Digital Optical Audio Out]
digital
optical cable
power cord
remote control
menu
controls
Blu-ray/DVD players: configure multi-channel output
If your soundbar is not producing sound or surround sound from your Blu-ray player,
DVD player, or other multi-channel audio capable source you may need to set the
player's digital audio output to "Bitstream" (also called "Raw", "Direct Digital", or
"High Bit Rate"). If "PCM" is selected you'll lose the multi-channel encoded sound.
Some players only require you to turn PCM off to configure for multi-channel
encoded sound. Please refer to your player's manual.
television: turn off speakers / turn on audio output
When utilizing the soundbar to reproduce audio, the television's speakers should be
turned off. Some televisions will allow you to turn off the internal speaker via the
television's menu system. Other televisions may require you to turn the television's
volume to "zero" or to "mute" the television. Please refer to your television's manual.
To pass audio out of your television, you may need to turn on the television's digital
audio out and set it for multi-channel output. Please refer to your television's manual.
Television
[connect to Digital Optical Audio Out]
Digital Out Digital Out
[digital optical] [digital optical]
[Analog In] [Sub Out] [Ethernet In] [AC Power In]
Purple [Coax In]
[Optical In]
[IR In]
Orange
connecting a subwoofer
no subwoofer
This is the factory default setting. If you are not using a separate subwoofer, use
the soundbar's menu system and choose "SUB > NO SUB". This sets the
soundbar to reproduce the entire frequency range when playing content.
wired subwoofer connection
Using a high-quality RCA style cable designed for subwoofer connection,
connect "Sub Out" from the soundbar to the "LFE In/Sub In" on the subwoofer.
Use the soundbar's menu system and choose 'SUB > WIRED'.
wireless subwoofer connection
Select MartinLogan subwoofers are equipped with a built-in SWT-2 wireless
receiver capable of establishing a wireless connection with this soundbar.
Use the soundbar's menu system and choose 'SUB > WIRELS > SYNC'. The
soundbar will display 'PSH.BTN' [PUSH BUTTON].
Press the subwoofer's sync button and hold for 3 seconds. The subwoofer's LED
will blink quickly. If pairing has completed successfully the subwoofer's LED will
stop blinking and remain on and the soundbar will display 'SYNCED'. Please
note: If a link is not established after 30 seconds the subwoofer's LED will start
blinking slowly and the soundbar will display 'FAILED'. Repeat if syncing fails.
adjusting your subwoofer's controls (wired and wireless connections)
Reference your subwoofer's manual to learn how to properly adjust the sub's
level and phase controls to achieve proper blending with the soundbar. The
subwoofer's crossover should be set to "bypass" or "LFE". For subwoofers that do
not have a "bypass" or "LFE" crossover setting we recommend adjusting the
crossover to its highest setting.
program soundbar to respond to a second remote
Start with the soundbar remote:
1) Press the "MENU" button.
2) Press down until you see the "LEARN" option. Press enter.
3) Press down and choose the command you want to program.
4) Press enter and the soundbar will respond with "PUSH.BTN".
Continue with the second remote:
5) Hold the second remote approximately 12-inches (30cm) from the
soundbar and press the appropriate button on the second remote four
times. If the command is learned successfully the soundbar will display
"SET". If it is not learned the soundbar will display "FAILED".
quick start guide
rev. 003