Luxibel LX104 Mode D'emploi page 5

6. Installation I
Refer to t the illustrations
6.1 O Overhead mo
•
Have e the device inst
norm ms.
•
The c construction to
devic ce for one hour
•
The i nstallation mus
•
Neve er stand directly
quali fied technician
•
Insta all the device in
•
Over rhead mounting
insta llation material
attem mpt to install th
resul t in serious inju
•
For t russ-mounting,
the ( folded) bracket
•
Adjus st the desired in
6.2 D DMX-512 con
•
When n applicable, co
the o other side to the
linke d through seria
and o output connecto
•
Maxi mum recommen
numb ber of fixtures o
•
A DM MX terminator is
or is in an electricall
digita al control signal
resist tor between pin
the c chain.
6.3 General G
•
Make e sure there is n
coolin ng.
•
Have e a qualified elec
•
All fix xtures must be
or dim mmer circuit, ev
•
The i nstallation has
7. O Operation
Refer to t the illustrations
7.1 M Menu Functio
menu m fun
buil
spe
sou
slav
V. 01 – 0 06/06/2012
n
s on page 2 of th his manual.
ounting
talled by a quali ified person, res
which the devic ce is attached sh
without deform ation.
st always be sec cured with a sec
y below the devi ce when it is be
check the devic ce once a year a
a location with few passers-by
requires extens sive experience
to be used... Ha ave the materia
e device yourse elf if you lack th
uries.
use an appropr riate clamp (not
.
nclination angle via the mounti
nnection
nnect an XLR ca able to the fema
e male 3-pin XL R input of the L
l linking. The lin nking cable shou
ors.
nded serial data a link distance is
on a serial data link is 32 fixtur
s recommended for installations
y noisy environ ment (e.g. disc
by electrical no oise. The DMX t
ns 2 and 3, whic ch is then plugg
no flammable m aterial within a
ctrician carry ou ut the electrical
powered directl ly off a grounde
ven if the rheos stat or dimmer c
to be approved by an expert b
s on page 2 of th his manual.
ons
nction
t-in programs
~
ed
~
nd mode
ve mode
LX104/L LX105
specting EN 605
hould be able to
condary attachm
eing mounted, r
and once before
y and inaccessib
: calculating wo
l and the device
ese qualification
t incl.) and fit a
ng bracket and
ale 3-pin XLR ou
LX104/LX105.
uld be a dual co
s 500 meters (1
es.
s where the DM
os). The termin
terminator is sim
ed into the XLR
50cm radius of
connection.
ed switched circ
channel is used
efore the device
desc ription
select t between switc
( = loop of
select t running speed
= slow,
set th he LED bar into
set th he LED bar into
5
598-2-17 and al ll other applicab
o support 10 tim mes the weight o
ment e.g. a safe ty cable.
removed or serv viced. Have a
you bring it int to service.
ble to unauthoris sed persons.
orkload limits, d etermining the
e itself checked regularly. Do n
ns as improper installation may
n M10 bolt thro ugh the centre
tighten the bra cket screws.
utput of a contr roller (not incl.)
Multiple LX104 4/LX105's can
ore, screened ca able with XLR in
1640 ft). Maxim um recommend
X cable has to r run a long dista
nator prevents c corruption of the
mply an XLR plu ug with a 120Ω
R output socket of the last devic
f the device and d there is sufficie
uit and cannot b be run off a rhe
solely for 0% to o 100% switch.
e is taken into s service.
ching and fading g built-in progra
~ )
d of the internal program
= fast
sound activated d mode
slave mode
ble
of the
not
y
of
and
be
put
ded
nce
e
ce in
ent
eostat
ams
©Vellem man nv