Publicité
Les langues disponibles
Les langues disponibles
SETUP INSTRUCTIONS
This is the safety alert symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal injury
hazards. Obey all instructions to avoid possible injury or death.
PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS.
1.
Attach fingers (#3) to saddle angles (#2) using bolts (#4), flat washers (#5) and nuts (#6).
2.
Attach saddle angles (#2) to saddle (#1) using bolts (#7), washers (#8) and nuts (#9).
3.
Attach and secure hook standoff (#11) to finger (#3) with washer (#5) and nut (#6) as shown in the exploded view drawing on page 4. Insert
adjustment hook (#12) through hook standoff (#11) and secure with washer (#5) and wing nut (#10).
4.
Secure one end link of chain (#13) to another finger (#3) with the bolt (#4), washer (#5) and nut (#6). Attach any other link of chain (#13) to
the adjustment hook (#12).
5.
Remove
service
jack
of the angle adjustment stand (#20) into the jack's saddle base and secure with the screw (#26), washers (#25), washer (#24) provided.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1.
Lift the vehicle to the desired work height, and support the vehicle in accordance with the lift manufacturer's recommended lifting and
support procedures.
2.
Position the jack directly under the transmission. Pump the handle, and the adapter will start to rise. Raise the adapter to a height very
close to the center of balance point of the transmission, but do not touch the transmission.
3.
Loosen the bolts that secure the saddle angles to the saddle and the bolts that secure the fingers to the saddle angles. The saddle
angles and fingers can be adjusted in and out to help position the transmission on the saddle. Now gently raise the adapter so it supports
the transmission. Make a final adjustment of the angles and fingers and tighten all hardware. Fore and aft saddle tilt adjustment may be
necessary to properly fit the angle of the transmission on the adapter.
4.
The chain should be pulled over the center of balance portion of the transmission and secured on the chain hook. Rotate the wing nut to
take up the slack in the chain and secure the transmission to the saddle.
5.
Remove the transmission from the engine according to instructions in the vehicle service manual.
6.
Once the transmission has been disconnected from the engine, very slowly turn the jack's release knob in a counterclockwise direction to
make sure the jack's saddle and transmission do not hang up on any under vehicle components, wiring, fuel lines, etc. Continue to lower
the jack all the way down.
7.
Remember to secure the transmission to the adapter before installing, and follow the vehicle manufacturer's installation instructions.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1.
Always store the adapter in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or
any other harmful elements. The adapter must be cleaned of water, snow, sand or grit before using.
2.
The adapter must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to
fore and aft tilt screw and tilt pivot pins.
3.
Every adapter owner is responsible for keeping the adapter labels clean and readable. Use a mild soap solution to wash external surfaces
of the adapter. Contact NAPA for a replacement label if your adapter's label is unreadable.
4.
Inspect the adapter before each use. Do not use the adapter if any component is cracked, broken, bent or shows sign of damage. Do not
WARRANTY
Please contact your local NAPA Auto Parts Store for details on warranty.
791-7130
OPERATING MANUAL & PARTS LIST FOR 791-7130
saddle
and
raise
jack's
lift
arm
to
maximum
3
height.
Insert
the
stud
at
the
bottom
rev. 12/11/15
Publicité
