Sunex Tools 8003SC Instructions D'assemblage

ASSEMBLY INSTRUCTIONS
#6.
Handle
#5.
Leg (x4)
Items Needed for Assembly:
#2 Phillips ® head screwdriver
10mm wrench
Assembly Instructions:
1. Using a 10mm size wrench, Phillips
and part #9 (bolt kit containing 16 short bolts, nuts
and washers), attach part #3 (2 non-locking casters)
and part #4 (2 locking casters) to each end of part #2
(bottom shelf with 16 pre-drilled holes).
2. Using the 10mm size wrench, Phillips
and part #7 (bolt kit 16 pieces of the 28 short bolts,
nuts and washers), attach part #5 (4 legs) to part #2
(bottom shelf).
3. Using the 10mm size wrench, Phillips
and part #7 (bolt kit –remaining 12 pcs. of the 28 short
bolts, nuts, and washers) attach part #1 (top shelf) to
the legs and bottom shelf.
Note: In order to place the handle on the same end as
the locking casters, leave the 4 outside holes open on
the locking caster end of the cart. Follow step 4 below
and attach the handle.
4. Using the 10mm size wrench, Phillips
and part #8 (bolt kit – 4 long bolts, nuts, and washers)
attach part #6 (handle) to the cart.
Replacement Parts Available:
RS8003LC Locking Caster (ea.)
RS8003SC Non-locking Caster (ea.)
RS8003CHDL Chrome Handle
8003SC
#4. Locking Caster (x2)
® head screwdriver,
® head screwdriver,
®
head screwdriver,
® head screwdriver,
#1. Top Shelf
(4 knockout
dimples in
bottom of tray
for optional
locking drawer,
8006RB)
#2. Bottom Shelf
(16 pre-drilled
holes in bottom
of tray for
attaching casters)
#3. Non-locking
Caster (x2)
Overall Load Capacity ................................................................. 350 Lbs.
Top Shelf Capacity ...................................................................... 175 Lbs.
Bottom Shelf Capacity ................................................................ 175 Lbs.
• It is the responsibility of the owner to make sure all personnel read this manual prior to using
the device. It is also the responsibility of the device owner to keep this manual intact and in a
convenient location for all to see and read. If the manual or product labels are lost or not legible,
contact Sunex Tools ® for replacements. If the operator is not fluent in English, the product
and safety instructions shall be read and discussed with the operator in the operator's native
language by the purchaser/owner or his designee, making sure that the operator comprehends
its contents. • Read and follow all instructions in User's Manual. • Do not load carts beyond
rated capacity (350 Lbs. - 175 lbs. per shelf). • Apply brake on locking casters anytime cart is
in place. • Do not pull cart. Push from handle on end to move. • Units can tip or fall causing
damage or personal injury. • Cart is designed to roll easily on flat surfaces and should not be
used on uneven or inclined surfaces. • Keep children away from unit. • Wear gloves when
lifting by edges. • Failure to heed these warnings may result in personal injury and/or property
damage.
WARNING: This product can expose you to chemicals including nickel,
which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
2-SHELF SERVICE CART
Long Bolt (x4)
Short Bolt (x44)
Nut (x48)
Washer (x48)
#7 Bolt Kit contains:
28 short bolts, nuts, and washers
for the legs
#8 Bolt Kit contains:
4 long bolts, nuts and washers
for the handle
#9 Bolt Kit contains:
16 short bolts, nuts, and washers
for the casters
WARNING
© Copyright 2019, Sunex Tools
8003SC
®
Rev. 04/23/19