Denver Electronics MRD-165 Guide D'utilisation page 8

5. After completing of recording, unit will stop playback automatically.
6. Press " stop " button (3) to interrupt the recording mode anytime.
7. For encode whole CD track, pls stay CD in stop mode then press "
" REC USB", then system will start to playback CD and encoding whole disc.
Remark:-
- The recording speed is 1:1 and according to the actual plying time of the CD track
- The recording format is preset at – MP3 bit rate : 128 kbps, sampling rate : 44.1khz
- Press " stop " button (3) to interrupt the recording mode at anytime.
B) Copying of MP3 file
If putting a MP3 disc instead of a CD-disc, the system will copy the files to the USB if press the "
procedures is same as CD encoding as stipulate on above, and the system will switch to copying mode only if MP3 file being read.
C) DAB encoding
1. Operate tuner mode refer above listening to radio section to receive the station you would like to encode.
2. Press the " " button twice (4) until the unit will display flashing with "REC USB " icon. Encoding is now performing.
3. After finish of recoding, press" stop
D) Cassette/Phono encoding
1) Plug in the USB pen drive or SD/MMC card for recording (make sure it had enough empty space).
2) Set the unit to your desired encoding mode by function button (10) such as " tape " mode or phono...etc and then start to
playback the track would like to encode, then press the "
3) The LCD display (2) will flashing with " REC USB " icon. Now the system is starting the encoding mode.
4) Start playback of cassette tape or your external Aux device which the track you prepare to encoding to MP3 format.
5) After finish of recoding, press" stop
E) track separation(On remote control only)
You can divide the recording music from tape or DAB...etc in to USB track by track during encoding. Every time when press the "
" (track separation) button (on remote control) once during encoding from tape or Aux in, the system will generate a new track and
continuous the recording. The text " SAVE " at LCD display will flashing one time, it mean the unit is creating a new track successfully.
F) Copying of MP3 file
If putting a MP3 disc instead of a CD-disc, the system will copy the files to the USB if press the "
procedures is same as CD encoding as stipulate on above, and the system will switch to copying mode only if MP3 file being read.
File delete at USB / SD card (by remote control)
The system is able to erase the file stored inside the USB pen drive by following:-
1． Insert the media storage and set at " USB " mode.
2． Press the " delete " button and the LCD display (2) will show (del ---001)
3． Press skip forward
4． Press the " delete " button to enter " yes / no " mode and then press skip forward
" no ".
5． Press the " delete " button again to confirm the setting.
Remark
:
- Press " stop " button once at remote handset to quite delete mode
Phono
noted:
Remove the stylus protector.
-
- Be sure that the tone arm is being detached from the tone arm rest before operating and re-secured
again afterwards.
1. Select to " Phono " function (10).
2. set the speed selector (27) to the proper position depending on the record to be played.
3. Place the record on the platter (use the spindle adaptor (26) if required).
4. Lift the tone arm from the rest and slowly move it to the record side. The platter will start to rotate.
5. Place the tone arm to the desired position of the record.
6. Adjust the volume to the desired level (19).
7. At the end of record, the platter will automatically stop rotating. Lift the tone arm from the record and return it to
the rest.
8. To stop manually, lift the tone arm from the record and return it to the rest.
Remark : as some kind of record the auto-stop area was out of the unit setting, so it will stop before the last rack finish. In this case,
select the auto-stop switch to " off " position, then it will run to the end of the record but will not stop automatically (turn off the power
button or switch back the auto-stop switch (28) to " on " position to stop the platter rotate). Then put back the tone arm to the rest
position.
" button (3) until the symbol " REC USB " disappear.
" button (3) until the symbol " USB " & "REC USB" disappear.
or skip backward button to select the file going to delete
" button (4) three times until the display flashing
" button (4) twice.
English – 7
" button (4). The operation
REC " button (3). The operation
or skip backward to select " yes " or