Publicité
Les langues disponibles
Les langues disponibles
MAINTENANCE AND REPAIRS
Premise: Continuous and extended use in time and the properties of the water supplied from the water
grid (calcium/impurities), may cause efficiency loss of the thermostatic cartridge. Maintenance/cleaning
or full replacement may be necessary.
Proceed as follows:
1.
Unscrew the levers (19) and the grub screws (18); take off the supply lever (10), the spacer ring (9) and
the diverter knob (8). Take off the temperature control knob (17) and the cam (16); also take off the cover
plate (20). (fig. 13)
2.
Close off the water supply firmly screwing in the grub screws of the ON-OFF caps (12). (fig. 14)
3.
Take off the housings (7) and (15), unscrew the nuts (3) and (14). It is advisable to protect contact between
operating key and nuts. (fig. 15)
4.
Take off the diverter cartridge (2) and wipe away any residue or deposits present in the seat.
5.
Insert the new diverter cartridge (2) paying careful attention to the studs protruding from its base; these
must fit into the appropriate seats (fig. 15). Make sure all positions are set to zero using the red markers on
the cartridge which must all be turned upwards (fig. 16). Screw the nut (3) and lock.
6.
Take off the thermostatic cartridge (13) and wipe away any residue or deposits present in the seat:
• in the case of maintenance activity immerse the cartridge in water and vinegar (50% + 50%) for
approximately 12 hours, eliminating any limescale and impurities, then carry on from point 8;
• if the cartridge needs to be replaced proceed from point 8;
7.
Insert the thermostatic cartridge (13); this cartridge does not have a predetermined position. Screw the
nut (14) and lock.
8.
Screw the housings (7) and (15).
9.
Position the cover plate (20).
10. Insert the diversion retaining ring (4) respecting the references highlighted in figure 17.
11. Insert the diverter knob (8) taking care to keep the lever in vertical position.
12. Place the spacer ring (9) in the appropriate seat of the diverter knob.
13. Insert the supply lever (10) with the lever seat turned downwards. Fix it in place with the appropriate grub
screw (18) and screw the lever (19).
14. Assure that the reference marks on the thermostatic cartridge (13) are aligned. (fig. 18)
15. Insert the cam (16) checking that the reference (A); respect the vertical axis.
16. Insert the temperature control knob (17) assuring that the red button (B) is upright and respect the
position with the outcropping reference (A). (fig. 19)
17. Check to make sure that temperature control knob (13). It can rotate clockwise, while to rotate it counter-
clockwise, it is necessary to push the red button (B) to have hot water above 38°C.
18. Insert it right to the bottom, lock it with the grub screw (18) and screw the lever (19).
19. Clean thoroughly with a rag (Fig. 18).
To assure functioning of the thermo-regulator, periodic adjustment of the thermostat is necessary,
switching from extreme hot water supply to extreme cold.
CLEANING
To keep the material's appearance as long as possible, a few guidelines must be followed.
Cleaning metal parts: water contains calcium that deposits on surfaces and forms unpleasant spots. For
routine cleaning,simply use a damp cloth with a little soap, rinse and dry. Calcium spots can therefore be
avoided by drying after use.
Important note: Using only a soap-based detergent is recommended. Never use abrasive detergents or
disinfectants or those containing alcohol, hydrochloric acid or phosphoric acid.
Dear Customer, we would like to remind you that the warranty on our product's surface is not valid if the
material undergoes treatment different than that suggested. The warranty does not cover any damage
due to deposits of calcium or impurities.
TERMOSTATICO 2/3/4/5 VIE
17
Publicité
