HELLER FSK 505 Instructions De Montage Et De Service page 5

If the supply cord is damaged, it must be replaced by the manufacturer or its
•
service agent or a similarly qualified person in order to avoid a hazard.
The power cable must not come into contact with the unit during heating
•
operation. Do not put the cable on or around the hot appliance and do not
pull it over sharp edges or bend it.
Do not use the heater outdoors.
•
The product is for household use only and not for commercial use.
•
The appliance is not suitable for animal breeding purposes!
•
Do not operate the heater with an extension-cord.
•
Do not use this heater with a programmer, timer, separate remote-control
•
system or any other device that switches the heater on automatically,
since a fire risk exists if the heater is covered or positioned incorrectly.
Attention! Even on the lowest setting level the unit is always ready
•
for use. In order to switch off the frost protector, pull out the power
supply plug or turn off the permanently installed disconnecting
switch (e.g. automatic cut-out, installation switch etc.).
Description
The frost protector is an electrical convector heater. It is fitted with a thermostat for the correct
temperature and a safeguard against overheating. A control lamp lights up when the frost
protector starts to heat up. The thermostat controls the room temperature and switches the
heater on or off as necessary. The built-in fixture for guarding against overheating switches the
unit off if too hot and switches itself on again after the unit has cooled down.
Mounting and electrical connection
Refer to the figures on the last pages. Be aware of keeping to the minimum distances
specified. Fix the mounting fixture to the wall (see figure). Two dowels and matching screws
are included on delivery. Drill the holes on the wall according to the distances specified in fig.
3. Use the bracket as a template for the 2 upper holes. Insert the raw plugs and screws (you
will find them inside the box) and then fix the wall bracket you find on the back of this item.
Then hang the heater to the bracket and drill the side screw which fixes the appliance to the
bracket.
After connecting the plug to the socket the heater is now ready for use.
The frost protector can also be permanently connected to the power supply by means of a
suitable junction box. This must only be carried out by a specialist. Protective conductor
necessary! It must be ensured that heaters which are permanently connected to the power
supply can be cut off by means of a disconnecting device with a minimum 3 mm contact gap
(e.g. automatic cut-out, installation switch, contactor etc.).
Operating instructions
The rotary knob and the marking on the casing show the setting of the thermostat.
To set the required room temperature: turn the knob in the direction of the arrow to the right as
far as it will go (ca. 90°) and wait until the required temperature has been reached. Turn the
knob then slowly back again until the control lamp has been extinguished. The position of the
knob now corresponds to the required temperature.
Taking care of your frost protector / Cleaning and maintenance
Before each cleaning, maintenance or repair disconnect the heater from the power supply.
Unplug the power cord from socket outlet or turn off the permanently installed disconnecting
switch (e.g. automatic cut-out, installation switch etc.) and let the heater cool down. Clean the
casing occasionally with a damp cloth and then wipe it dry. Do not use any strong abrasive
cleaning materials and do not let water get into the inside. Do not immerse the heater, power
cord or plug in water or other liquids. Danger of life!
Troubleshooting
Fault Possible cause
• •
Does not heat up Fuse blown
•
(control lamp does not
Plug disconnected
•
light up)
Room temperature
higher than the setting
•
Overheating device has
reacted.
If the fault cannot be corrected by any of the above measures, contact your local specialist or get in
touch with our after-sales service. Repairs may only be made by authorised specialist or our after-
sales-service.
Guarantee
• If problems occur with the device never try to open or repair by yourself. Every intervention in the
unit for the change of original condition leads inevitably to the loss of the guarantee claim. Contact
the retailer where you have purchased the appliance. The guarantee for this device is based on the
guarantee instructions.
• Damages which occur to transport, overloading, natural erosion, non observance of the mounting-/
operating instructions or improper treatment will be excluded from the guarantee. The manufacturer
is not liable for any indirect consequential or financial damages.
• Technical changes concerning the advancement are reserve.
Disposal
The symbol on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your local authority,
your household waste disposal service or the shop where you purchased the product. This symbol is only
valid in the European Union.
Setting of the required room
temperature (max. 16°C)
Measures
•
Check fuse box
•
Reconnect plug
•
If possible, set a higher
temperature
•
Do not cover frost protector with
any objects. Keep to min.
specified distances!