Service And Maintenance Instructions; Troubleshooting; Technical Data; Putting Out Of Operation/Waste Disposal - Klauke ES 85-L Mode D'emploi

Instruction Manual Cutting Tool
ES 85-L ES 105-L
4.3 Service and maintenance instruction
For every day service the tool has to be cleaned and dried
after each use. The battery cartridge and the charging unit
have to be protected against humidity and dust.
The electric-hydraulic unit is equipped with a controller
enabling the user to see when the next service is due by
fl ashing for 20 sec. at the end of a working cycle.
The unit must be sent to an authorized service center
(ASC) after reaching 10.000 cycles or at the latest after
one year. During this service worn out parts will be ex-
changed, safety relevant components checked and pos-
sibly replaced pre cautiously. This provision serves your
safety and avoids failures through fatigue.
Attention
Maintain power tools thoroughly. Check for
functionality or jamming of moving parts,
breakage of parts and any other condition that
may affect the power tools operation.
Attention
Do not damage the seals of the tool. If the seal
is damaged the warranty claim is void.
Attention
Have damaged parts repaired by a qualifi ed ex-
pert or by a Klauke ASC before use.
Attention
Keep the blades clean and grease the guidance
regularly.
5.

Troubleshooting

a.) Constant fl ashing/indicating of the light diode display
(page I, pic 1, 1).
see table 1. If the failure can not be solved through
the action recommended in table 1 return the tool to
the nearest service center (ASC).
b.) The tool loses oil.
Return the unit to the manufacturer. Do not open it
and damage the seal of the tool.
6.

Technical Data

Weight (incl. battery):
Cutting force:
Maximum cutting diameter:
Driving motor:
Battery voltage:
Battery capacity:
Charging time:
Cutting time:
Crimp per battery:
Hydraulic oil:
Environmental temperature:
Sound level:
Vibrations:
Dimensions:
HE.13465_C © 05/2010
ES 85-L
approx. 6,3 kg
approx. 30 kN
Ø 85 mm
direct-current permanent fi eld motor
18 V DC
3 Ah (RAL2/BL1830)
22 min. (RAL2/BL1830)
approx. 9 s to 19 s
(depending on the connector size)
approx. 70 cuts (4 x 240 mm² NYY)
Rivolta S.B.H. 11
-12°C bis +40°C
< 70 dB (A) in 1m distance
< 2,5 m/s²
See pic. 2
7. Putting out of operation/waste dis-
posal
This unit is subjected to the scope of the European WEEE
(2002/96/EG) and RoHS (2002/95/EEC) directives.
Information about this can be found in our home page
www.Klauke.com under 'WEEE & RoHS'.
Battery cartridges must be specially disposed of accor-
ding to the EEC Battery Guideline.
Attention
Do not dispose of the unit in your residential
waste. Klauke has no legal obligation to take
care of their WEEE outside Germany unless the
product has been shipped and invoiced from
inside your country by Klauke. Please contact
your distributer to fi nd out more how to get your
tool recycled environmental friendly.
Kontaktadresse:
WEEE-Abholung@Klauke.Textron.com
Attention
Additional instruction manuals are available
free of charge. The part # is HE.13465.
struction Manual can also be downloaded from
our Homepage www.klauke.textron.com.
ES 105-L
approx. 8,,8 kg
approx. 74 kN
Ø 105 mm
approx. 11 s to 23 s
(depending on the connector size)
approx. 60 cuts (4 x 240 mm² NYY)
The In-
3
GB