Password Setup; Firmware Update - Intermatic ET90000 Serie Guide D'installation Et De Programmation

Minuterie électronique
Masquer les pouces Voir aussi pour ET90000 Serie:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

A)
PROGRAMMED SCHEDULE
From REVIEW
MODE, you land
on PROGRAMMED
SCHEDULE. After you
choose which circuit's
schedule you would
like to review, you land
on SELECT EVENT
TYPE. From this
screen, select from the following:
• ALL EVENTS
• HOLIDAY EVENTS ONLY
• RELATIVE EVENTS ONLY
Select the date of the event you would like to review and
press enter. The screen shows any event scheduled.
B)
EVENT LOG
You can also view an
EVENT LOG, such as
this example. The event
log stores the most
recent 1,000+ events
and can be saved to
USB.
2.
proG Copy/resTore
Under this function, you can copy or restore a program
into the ET90000-series timer from the USB port. To copy
a program, insert a USB drive into the port and follow the
prompts. To restore a program, select which program you
would like to restore from the list on the screen; press
ENTER to delete the current schedule and replace it with
the saved USB schedule. Note: Backup your schedule to
USB in case it is unintentionally modified, reset, etc.
3.

passWord seTup

On this screen, your choices are:
• ENABLE PASSWORD
• CHANGE PASSWORD
In ENABLE PASSWORD, your choices are ENABLED
and DISABLED. When you select ENABLED, it means
screens are viewable but you must enter the password
to change or add information. Choosing DISABLED
means no password is necessary to view, change or add
information.
To change the password, press CHANGE PASSWORD.
After you land on the SYS PSWORD CHANGE screen,
key in up to 10 alphanumeric characters; key in again to
confirm. Write down password!
SYS. REVIEW-MODE
CIRCUIT 1
SELECT EVENT TYPE
ALL EVENTS
HOLIDAY EVENTS ONLY
RELATIVE EVENTS ONLY
EVENT LOG
PARKING L1
12/31/12
ON
5:00 PM
-MANUAL-
12/31/12
OFF
2:00 PM
-SERIAL-
12/31/12
ON
10:00 AM
Note: If the password is enabled, you can still reset the
device to factory defaults.
IMPORTANT: You can reset to factory defaults even if you
do not know the password; in fact, this is the only way
to start "from scratch," and enter a new password, if the
password is permanently lost. Always copy the schedule
to USB prior to resetting the timer.
4.
edIT sysTem name
Use this for identification purposes to name your system
when networking multiple timers together. Change or
edit the system's name using up to 10 alpha/numeric
characters, then press ACCEPT.
5.
neTWork seTup
In NETWORK SETUP, you can:
• CONFIGURE NETWORK ADDRESS – If you
would like to connect to a network, you must
configure the network address. ENTER the IP
(internet protocol) address, the subnet mask, and
the default gateway.
• CONFIGURE REMOTE ADDRESS – To configure
a remote address, you must first connect to an
Ethernet device (see page 7). Then you can
program up to 16 IP addresses.
• REMOTE CONNECT – Follow the prompts to
connect to another Ethernet device.
• REMOTE DISCONNECT – First connect to an
Ethernet device, then follow prompts.
• TIME SYNC – Sends the time information from
the current timer to all timers, so clocks are
synchronized. To synchronize timers, first connect
to an Ethernet device, then follow the prompts.
6.

fIrmWare updaTe

Firmware updates are available at
http://www.intermatic.com. To install an update from a
flash drive, insert drive into the USB port, then follow the
prompts.
7.
reseT faCTory defaulTs
Choose NO or YES. Be certain you want to do this!
IMPORTANT: Copy the schedule to USB prior to resetting
the timer. If you reset factory defaults, you lose all custom
programming.
15
ET90000 Series Electronic Timer

Publicité

Table des Matières
loading

Table des Matières