Publicité
Les langues disponibles
Les langues disponibles
PREPARATION
Build solid framing to the dimensions in Figure 1.
·
Ensure that the floor is level, shim tub if necessary.
·
The drain location on the tub shower is shown in
·
figure 1.
Drain pipe must be vertical.
·
Trim drain pipe as required to meet drain assembly.
·
Place the unit into position and plumb vertical, shim if
·
necessary.
Dry fit drain to check position.
·
Mark and drill 3/16" pilot holes for plumbing fixtures.
·
Verify that the holes are in the right location.
·
From the finished side of the unit use the correct size
·
hole saw to cut the openings, using the pilot holes as
guides.
INSTALLATION
Carefully position the Tub Shower into the framing
·
and push flush against the framework walls.
Install the drain according to the manufacturer's
·
instructions. Use a mildew resistant silicone
bathroom caulking to seal the drain to the top surface
of the tub.
Fasten the acrylic unit to the framing using drywall
·
screws. Countersink for screw head flush fit on the
acrylic flange. Please note to make sure that the unit
is plumbed before fastening.
Apply silicone caulking over the head of the screws
·
and around the openings for the fittings when they are
installed.
TROUBLESHOOTING
Tub bottom section is not level: Refer to shimming
·
section on page 1.
Water remains around the bathrim or drain: Check
·
that the installation is level and that the tub sits firmly
on its base; use wood shim to correct.
FINISHING
Apply trim around the tub shower periphery to finish
·
drywall, if required.
Install
Mirolin Shower Door TD 55 (Tri-panel) or BD
·
55 (Bypass)
according to manufacturer's instructions if
purchased.
60 Shorncliffe Rd., Toronto, Ontario M8Z 5K1
Telephone: (416) 231-9030 - Fax: (416) 231-0929
Customer Service: (416) 231-5790
Canada, U.S.A.: 1-800 -
Fax, Canada: 1- 800 - 463 - 2236
The company reserves the right to change models and specifications without notice.
MIROLIN
(647-6546)
INSTALLATION CLEAN-UP
It is important to remove all construction debris and
·
foreign materials.
Remove construction dirt and residue with a mild
·
liquid detergent. DO NOT USE abrasive cleaners,
scouring compounds and pads, metal scrapers, steel
wool, or other materials that could damage or dull the
surface of the bath.
Remove plaster carefully with a blunt wooden block
·
having rounded edges.
Remove paint and other stubborn stains with
·
isopropyl (rubbing) alcohol.
DO NOT USE products such as acetone (nail polish
·
remover),dry cleaning solution, lacquer thinners,
gasoline, pine oil, etc.
Test the installation after completing the plumbing,
·
but before enclosing the bath and finishing the
surroundings.
Fill the bath with water and leave for one hour to
·
ensure that the adjustment of the drain-overflow
assembly is correct, and that there are no leaks.
MAINTENANCE
The acrylic sheet which forms the surface of your bathtub
provides one of the most durable
modern bathrooms. Keep it bright and smooth with mild
liquid household detergent, soap and water, or foaming
cleansers. NEVER USE aromatic solvents, abrasive
cleaners, scouring compounds or pads, strong liquid
cleansers, or other material that could damage or dull the
surface of the bath.
We recommend the use of Mirogloss Acrylic and
Fiberglass Polish before use and then periodically to
preserve the appearance of your bath.
and Fiberglass Polish is available from your dealer.
Restoring Surface Gloss.
applying a very fine rubbing compound and polishing the
surface by hand or with a power buffer. Finish with an
®
application of Mirogloss or a good quality automotive
wax.
Minor Repairs to Surface.
scuffs as follows. First, wet sand the area with 600 grit wet
sandpaper until the surface is smooth. Finish with 1200
grit wet sandpaper, then restore the gloss as described
under RESTORING SURFACE GLOSS.
C
surfaces found in
®
®
Mirogloss Acrylic
Restore surface gloss by
Remove minor scratches and
US
84 069
23 Mar.12
3
Publicité
