Generac 6565 Manuel De L'opérateur page 13

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

CLEANING AND APPLYING DETERGENT
WARNING
Chemicals can cause bodily injury, and/or
property damage.
• NEVER use caustic liquid with the power washer.
• Use ONLY power washer safe detergents/soaps. Follow all
manufacturer's instructions.
To apply detergent, follow these steps:
1. Review proper use of nozzles.
2. Prepare detergent solution as required by the job into a
container located within the proximity of the siphon tube.
3. Make sure the siphoning tube remains fully submerged into
the detergent.
Make sure the filter remains fully submerged in detergent
while applying detergent.
Contact with the hot muffler can damage the detergent
siphoning tube.
4. When inserting the siphon into a detergent solution bottle, route the
tube so as to keep it from inadvertently contacting the hot muffler.
5. Make sure the black detergent nozzle is installed.
Detergent cannot be applied with the high pressure nozzles
(Yellow, White, Green or Red). Only use the Black nozzle with
detergent.
6. Confirm that all set-up instructions have been followed.
You must attach all the hoses before you start the engine.
• Starting the engine without all the hoses connected, and without
the water turned ON, will damage the pump.
• Damage to the equipment resulting from failure to follow these
instructions will void the warranty.
7. Start engine following instructions How to Start Your Power
Washer.
8. Apply detergent to a dry surface, starting at the lower portion
of the area to be washed and work upward using long, even,
overlapping strokes.
9. Allow the detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent the
surface from drying. DO NOT allow the detergent to dry on the
surface being cleaned (prevents streaking).
IMPORTANT: You must flush the detergent siphoning system after
each use by placing the filter into a bucket of clean water, then run
the power washer in low pressure for 1-2 minutes.
(000126)
NOTE:
NOTE:
NOTE:
NOTE:
POWER WASHER RINSING
1. Remove the black detergent nozzle from the lance.
2. Select and install the desired high pressure nozzle following
the instructions How to Use Nozzles.
3. Point the spray gun in a safe direction and away from people,
animals and plants. Squeeze the trigger to flush any remaining
chemicals from the system.
4. Keep the spray gun a safe distance from the area you plan to
spray.
WARNING
Risk of Falling. Use of machine creates wet areas
and trip hazards. Be aware of work area conditions.
A fall could result in death or serious injury.
Risk of Falling. Do not use this machine or any
components on elevated surfaces. Doing so can
result in a fall, serious injury or death.
Recoil Hazard. Recoil could retract unexpectedly
if water pressure is not properly relieved from
pump, creating kickback. Kickback
could result in death or serious injury.
• Use only on a level surface.
• Do not use on an elevated surface to prevent the risk of a serious fall.
• Firmly grasp the spary gun with both hands when using the high
pressure spray to avoid injury when the spray gun kicks back.
5. Apply a high pressure spray to a small area and then check
surface for damage. If no damage is found, you can assume
it is okay to continue rinsing.
6. Start at the top of the area to be rinsed, working down with the
same overlapping strokes used for cleaning.
CLEANING DETERGENT SIPHONING TUBE
If you used the detergent siphoning tube, you must flush it with
clean water before stopping the engine.
1. Place the detergent siphoning tube/filter in a bucket full of
clean water.
2. Remove the high pressure nozzle from the nozzle extension.
3. Select and install the black detergent nozzle following the
instructions How to Use Nozzles.
4. Flush for 1-2 minutes.
5. Shut the engine off following the instructions How to Stop
Power Washer, and turn off water supply.
6. ALWAYS point the spray gun in a safe direction, squeeze the
spray gun trigger to release retained high water pressure.
Engage the trigger lock when not in use.
Set-up
WARNING
WARNING
(000112)
(000114)
(000113)
11

Publicité

Table des Matières
loading

Table des Matières