Cleaning And Maintenance; Technical Data - Asist AE6CS08 Mode D'emploi

• Make sure when doing so that the mounting
plate of the chain sharpener is pushed 8 cm
onto the surface (Fig. 6)
Operation
Important! Always switch the appliance off and unplug
the power plug before making any adjustments.
Insert the chain that is to be sharpened
into the chain bar (Fig. 7)
To do this, loosen the chain locking screw (1)
Set the grinding angle according to the specifi ca-
tions for your chain (Fig. 8) (normally between 30-35°)
• Slacken the locking screw for setting the grinding
angle (1)
• Set the desired grinding angle using the scale (2)
• Tighten the locking screw (1) again
6.3 Set the chain stopper (Fig. 9/10)
• Fold the chain stopper (1) onto the chain
• Pull the chain backwards against the chain stopper
(1) until the latter stops a cutting link (2). Important!
You must make sure that the angle of the stopped cut-
ting link coincides with the grinding angle. If it does
not, pull the
chain one link further.
• Fold the grinding head (4) down until the grinding
wheel (5) is touching the chain link (6)
that is to be ground. (To do so, you can move
the chain back and forth a little using the setting
screw of the chain stopper (3)
Set the depth limit (Fig. 10)
Fold the grinding head (4) down and set the grinding
depth using the setting screw (7) Important! The grin-
ding depth should be set so that the full cutting edge of
the cutting link is sharpened.
Lock the chain (Fig. 7)
Tighten the chain locking screw (1)
Grinding the chain links (Fig. 10/11)
Important!
• Only use the equipment for sharpening saw chains.
Never grind or cut other materials.
• Before sharpening the saw chain clamp it into
the chain bar. This will prevent jamming of the
grinding wheel caused by a loose saw chain.
• Slowly guide the grinding wheel to the saw
blade. If the grinding wheel approaches the saw chain
too quickly or jerkily, this may cause damage to the
grinding wheel. Injuries may result from catapulting
parts!
• Switch the appliance on at the ON/OFF switch (1)
• Carefully bring the grinding wheel (5) with grinding
head (4) so that it is against the set link • Switch the
appliance off at the ON/OFF
switch (1).
Every second link in the chain
must be sharpened in this way. To know when every
second link in the entire chain has been sharpened,
mark the first link (e.g. with chalk). Once all cutting
links on one side have been sharpened, the grinding
angle must be set to the same number of degrees on
the other side. You can then begin to sharpen the links
of the other side(without having to make any
further adjustments).
Set the depth limiter spacing (Fig. 12/13)
Once the chain has been fully sharpened, you
must make sure that the depth limiter spacing is
kept (the depth limiters (1) must be lower than the
cutting links (2). You may need to fi le the depth
limiters (1) to the specifi cations for your chain
using a fi le (3) (not included in delivery).
Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Changing the grinding wheel
Important! Always switch the appliance off and
unplug the power plug before carrying out any
maintenance.
1. Remove the grinding wheel (Figs. 14-16)
2. Fit a new grinding wheel
3. Assemble in reverse order
Do not use grinding wheels that are worn, broken,
cracked or otherwise damaged. Use only genuine grin-
ding wheels.

CLEaNiNg aND maiNTENaNCE

Danger!
Always pull out the mains power plug before starting
any cleaning work.
• Keep all safety devices, air vents and the motor hou-
sing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it with compre-
ssed air at low pressure.
• We recommend that you clean the device
immediately each time you have finished
using it.
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of the
equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool inc-
reases the risk of an electric shock.
Maintenance
• The equipment is maintenance free. Storage
• Store the appliance in a dry place well out of reach
of children.
• Grinding disks must be stored dry and upright and
are not to be stacked.

TECHNiCaL DaTa

44
aE6CS08