Publicité
Les langues disponibles
Les langues disponibles
OPERATION
Always turn off the air supply, drain hose of air pressure and detach
tool from air supply before installing, removing or adjusting any part or
accessory on this tool, or before performing any maintenance on this
tool.
Never operate the tool without a Chisel Retainer.
Never use a chisel as a hand struck tool. They aredesigned and heat
treated to be used only in air hammers. Select the correct shank and
retainer for the tool.
Never use dull, chipped or damaged accessories. Never cool a
hot accessory in water as brittleness and early failure can result.
Accessory breakage or tool damage may result from prying. Take
smaller bites to avoid getting stuck.
The Quick Change Chuck is designed to accept only 0 .401" diameter round
shank chisels . Always place the chisel in the hammer's quick change chuck
retainer and hold the tool down to the work before operating . Damage to the
tool or the retainer may result if this precaution is not followed .
The chisel retainers are not designed for complete safety against accidental
release of chisels or hammers . To avoid injury, the throttle must never be
depressed unless the chisel is held firmly against the work place . When tool
AIR SUPPLY
Tools operate on a wide range of air pressures. It is recommended
that air pressure measures 90 psig at the tool with the trigger fully
depressed and no load applied to the tool. Higher pressure (over
90 psig; 6.2 bar) raises performance beyond the rated capacity of
the tool, which will shorten tool life and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in
the air line will cause damage to the tool. Drain the water from
air lines and compressor prior to running tool. Clean the air inlet
filter screen weekly. The recommended hookup procedure can
be viewed in the Figure 1.
The air inlet used for connecting air supply has standard 1/4" NPT.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be
3/8" I.D. and fittings should have the same inside dimensions and
be tightly secured.
Always turn off the air supply, drain hose of air pressure
and detach tool from air supply before installing, removing or
adjusting any part or accessory on this tool, or before performing
any maintenance on this tool.
Ensure an accessible emergency shut off valve has been installed
in the air supply line and make others aware of its location.
MT2816
MT2816 LONG BARREL AIR HAMMER
Whip Hose
Do Not Install
Quick Coupling
Nipple
Here
Leader
Quick Coupler
Hose
is not in actual use, the chisel must be removed . When using tool, regulate
the speed so that the chisel is not being driven out of the cylinder . If piston is
allowed to strike the cylinder wall, internal damage will result .
To change chisel, pull back on quick change chuck collar and insert chisel .
Release chuck collar to lock in the chisel .
To regulate power, gently pull the variable speed trigger for minimum to
maximum power .
NOTE: During operation, safety goggles must always be worn to guard
against flying debris (users and bystanders).
TROUBLESHOOTING
Other factors outside the tool may cause loss of power or erratic
action . Reduced compressor output, excessive drain on the air line,
moisture or restrictions in air pipes or the use of hose connections
of improper size or poor conditions may reduce air supply . Grit or
gum deposits in the tool may cut power and may be corrected
by cleaning the air strainer and flushing out the tool with gum
solvent oil or an equal mixture of SAE #10 and kerosene . If outside
conditions are in order, disconnect tool from hose and take tool to your
nearest authorized service center .
LUBRICATION AND MAINTENANCE
Lubricate the air motor daily with high quality air tool oil. If no air
line oiler is used, run 1/2 oz. of oil through the tool. The oil can
be squirted into the tool air inlet or into the hose at the nearest
connection to the air supply, then run the tool. A rust inhibitive oil
is acceptable for air tools.
WARNING: After an air tool has been lubricated, oil will discharge
through the exhaust port during the first few seconds of operation.
The exhaust port must be covered with a towel before applying
air pressure to prevent serious injury.
Filter
Nipple
Oiler
Regulator
3
Air Supply
Drain Daily
FIG. 1
rev. 11/22/17
Publicité
