Notes; Technical Data; Standard Type - DOLD SAFEMASTER LG 5925.03/034 Manuel D'utilisation

Notes

Line fault detection on On-button:
The line fault detection is only active when S12 and S22 are switched
simultaneously. If The On-button is closed before S12, S22 is connected
to voltage (also when line fault across On-Button), the output contacts will
not close. A line fault across the On-button which occurred after activation
of the relay, will be detected with the next activation and the output con-
tacts will not close.
The terminal S21 permits the operation of the device in IT-systems with
insulation monitoring, serves as a reference point for testing the control
voltage and is used to connect the loop when cross fault monitoring is
selected.
Connecting the terminal S21 to the protective ground bridges the internal
short-circuit protection of Line A2 (-). The short-circuit protection of line
A1 (+) remains active.
To alter the functions automatic start - manual start and with or without
cross fault monitoring, the switches S1 and S2 are used. These are loca-
ted behind the front cover (see unit programming).
The setting with or without cross fault monitoring is made with S1.
Switch S2 is used to select automatic or manual restart. Additionally, for
the function "automatic restart", terminals S33 and S34 have to be bridged.
Connect the device according to application examples.

Technical Data

Input circuit
Nominal Voltage U :
N
LG 5925:
Voltage range:
Nominal consumption at U :
N
Min. Off-time:
Control voltage on S11 at U : DC 22 V
N
Control current typ. over
S12, S22
Min. voltage on S12, S22
when relay activated
Short-circuit protection:
Overvoltage protection:
Output
Contacts:
The NO contacts are safety contacts.
The NC contacts 41-42 can only be used for monitoring.
Operate delay typ. at U :
N
Manual start:
Automatic start:
Release delay typ. at U :
N
Disconnecting the supply:
Disconnecting S12, S22:
Contact type:
Nominal output voltage:
Thermal current I :
th
Switching capacity
to AC 15:
NO contacts:
NC contacts:
to DC 13:
NO contacts:
NC contacts:
Electrical contact life
to 5 A, AC 230 V cos ϕ = 1:
Permissible operating
frequency:
Short circuit strength
max. fuse rating:
line circuit breaker:
Mechanical life:
AC/DC 24 V
0.9 ... 1.1 U
N
DC ca. 1.5 W
250 ms
30 mA at U
N
DC 20 V
Internal PTC
Internal VDR
3 NO, 1 NC contact
30 ms
350 ms
Typ. 20 ms
Typ. 15 ms
Forcibly guided
AC 250 V
DC see arc limit curve
Max. 5 A per contact
(see quadratic total current limit curve)
3 A / AC 230 V IEC/EN 60947-5-1
2 A / AC 230 V IEC/EN 60947-5-1
2 A / DC 24 V IEC/EN 60947-5-1
2 A / DC 24 V IEC/EN 60947-5-1
> 2.2 x 10 switching cycles
5
Max. 1 200 operating cycles / h
10 A gG / gL IEC/EN 60947-5-1
B 6 A
> 20 x 10 switching cycles
6
Technical Data
General Data
Operating mode:
Temperature range
operation:
storage :
altitude:
Clearance and creepage
distances
Rated impuls voltage /
pollution degree:
EMC
Interference suppression:
Degree of protection
Housing:
Terminals:
Housing:
Vibration resistance:
Climate resistance:
Terminal designation:
Wire fixing:
Mounting:
Weight:
Dimensions
Width x height x depth
LG 5925:
LG 5925 PC:
LG 5925 PS:

Standard Type

LG 5925.03/034 AC / DC 24 V
Article number:
• Output:
• Nominal voltage U :
N
• Width:
14
Continuous operation
- 15 ... + 55 °C
- 40 ... + 85 °C
≤ 2000 m
4 kV / 3 (basis insulation) IEC 60664-1
IEC/EN 61326-3-1, EN 12016
Limit value class B EN 55011
IP 40 IEC/EN 60529
IP 20 IEC/EN 60529
Thermoplastic with V0 behaviour
according to UL subject 94
Amplitude 0.35 mm IEC/EN 60068-2-6
frequency 10 ... 55 Hz
15 / 055 / 04 IEC/EN 60068-1
EN 50005
Plus-minus terminal screws M 3.5
box terminals with wire protection or
cage clamp terminals
DIN rail IEC/EN 60715
210 g
22.5 x 90 x 121 mm
22.5 x 111 x 121 mm
22.5 x 104 x 121 mm
0064797
3 Schließer, 1 Öffner
AC/DC 24 V
22,5 mm
LG 5925.03/034 / 18.11.21 en / 466A