Intercom Feature; Making Calls With Bteasy; Led Indicator; Care And Maintenance - Cellularline BTEASY Manuel D'utilisation

BTEASY
notes:
- Pairing mode will last 2 minutes . BTEASY will switch
to standby mode automatically if it can't pair with
any devices after 2 minutes . If you want to continue
to pair the BTEASY with a Bluetooth® device, please
turn off BTEASY first and try to re-pair according to
steps 1-6 mentioned above .
- BTEASY will turn off automatically when it can't con-
nect to any devices after 5 minutes .
- BTEASY can remember 8 paired devices, when the
number of paired devices exceeds 8, the first one will
be replaced .
- When BTEASY is on but doesn't connect to any
devices, press mfB button of BTEASY once, it will
connect to the last connected device automatically .
- Every time BTEASY is turned on, it will connect to
the last connected device automatically . If you want
to pair it with other devices, please turn off the cur-
rent device's Bluetooth® function first and try to pair
BTEASY with the new device according to steps 1-6
mentioned above .
- When BTEASY gets out of working range of the con-
nected devices it will automatically reconnect to the
devices as soon as it is in working range again, either
it was connected to a interphone or a Bluetooth® cell
20
phone .

4. intercom feature

If two interphones connect each other, you are able to
use intercom feature . Specific operations are as follows:
function operation or status indication tone
Receive intercom Ringing Ring
Press and hold vol+
or vol– for about 2
Send out
seconds, and release 1 short tone
intercom
it after hearing "DU"
tone
Short press mfB
button when
Cancel intercom 1 short tone
intercom is not put
through
Short press mfB
Answer intercom 1 short tone
button
Press and hold mfB
button for about
Reject intercom 1 short tone
2 seconds when
receiving intercom
Short press mfB
End intercom 1 short tone
button

5. making calls with BteasY

If BTEASY is connected to a Bluetooth® cell phone, now
you can make calls with BTEASY . The specific operations
are as follows:
function Basic operation indication tone
Incoming ring Auto-ringing Ringing
Short press mfB
Redial last number button twice 1 short tone
quickly
Short press mfB
button when the
Cancel calling 1 short tone
call is not put
through
Short press mfB
Answer a call 1 short tone
button
Long press mfB
Reject a call button for 2 sec- 1 short tone
onds
Short press mfB
End a call 1 short tone
button
Short or long press
Volume up None
vol+ button
Short or long press
Volume down None
vol– button
notes:
- When the volume is adjusted to max . or min . you will
hear two "DU" tones .
BTEASY

6. led indicator

a) When it is charging
led indicator status of BteasY
Red LED is on Charging in progress
Red LED is off Charging finished
b) When it is not charging
led indicator status of BteasY
Red and blue LEDs flash Pairing mode
alternately
Blue LED flashes once every 3 Standby mode (not
seconds connected)
Blue LED flashes twice quickly Standby mode
every 4 seconds (connected)
Blue LED flashes twice quickly Incoming call/calling
every 4 seconds
Blue LED flashes slowly During a call
Red LED flashes Low power

- Care and maintenanCe

Read the following recommendations before using
BTEASY . Following these you will be able to enjoy our
product for many years .
- Keep it dry and don't take it to damp places to avoid
the product's internal circuit being affected .
- Keep the product away from direct sunlight or hot
places . High temperatures will shorten the life of
electronic devices, destroy the battery or distort
certain plastic parts .
- Don't expose the product to cold areas . It may dam-
age the internal circuit board .
- Don't try to disassemble the product as it may get
damaged if you are not professional .
- Don't let it fall down onto the floor or other hard
surfaces . The internal circuit might get damaged .
IT
EN
FR
ES
DE